Search results

  1. alldodge

    Bravo 3 shifting stiff. Cures?

    With motor running and lower shift cable removed from shift plate, can it be moved by hand with little effort FWD/REV? If it can lower is good, and problem is the throttle handle or throttle shift cable
  2. alldodge

    VP 4.3GL Bogging over 3000rpm

    What were your compression numbers? Timing 10* BTDC
  3. alldodge

    Will Vesselview Mobile work on my 4.3MPI

    The SN shows 555 ECM NO expert but if the motor has a CAN buss with the 14 pin connector, then it should work Would suggest Rinda scanner over vessel view. Either Diacom software or Techmate Pro. This way there is no need to check out how to install VV just get one of the above and the...
  4. alldodge

    Hurth transmission help

    If the dipstick has threads then its checked by not threading in. If dipstick does not have threads then its inserted fully to check Oil pressure should be 25bar (363 psi) No for sure but there is a allen hex plug on the shift selector, should be able to get the pressure reading from it Is the...
  5. alldodge

    Boat Wouldnt

    Still thinking Neutral safety switch Turn key to start and hold, now grab the throttle and move it slightly FWD and REV to see if it cranks If it doesn't then put a volt meter on the small yellow/red wire on the start assist relay. Turn key to start and see if there is 12V on the wire
  6. alldodge

    Hunting Turkey w/o a license cost over $800

    Dealer was closed Thanks, Did find someone which was changing out the head lights making his truck into a night edition, so I should be able to do it easy enough
  7. alldodge

    Hunting Turkey w/o a license cost over $800

    Going to call the dealer to see what the labor cost would be. Might do it my self if I can figure out how it comes apart. Will use some clear packing tape to hold the lens on until its done.
  8. alldodge

    7.4 mpi doesn’t want to idle?

    Get them cleaned and flow tested
  9. alldodge

    2012 Axis

    Manufactures defect that was not caught by QA
  10. alldodge

    Hunting Turkey w/o a license cost over $800

    Didn't know but I was hunting turkey without a license and one head light is $857. I hit the hen and tossed it into another pickup going the other direction, feathers everywhere. It just busted the lens but like all things, have to buy the whole light. Have to figure out what its going to...
  11. alldodge

    7.4 mpi doesn’t want to idle?

    Pressure is good Connect a vacuum gauge up to the intake, probably the line that connects to the fuel pressure regulator. Need a scanner to see what the MAP and IAC are seeing. Could measure voltage of the 2 but a scanner would be better
  12. alldodge

    Trim sensor/limit & speedometer not working after lower unit work

    Keep looking there are 2 more. All 4 come from the top of the transom assembly
  13. alldodge

    Trim sensor/limit & speedometer not working after lower unit work

    Look at the rear of the motor and by the trim pump. The trim wires may have been disconnected. They are black with bullet connectors.
  14. alldodge

    7.4 mpi doesn’t want to idle?

    Is this a new to you boat, or a new problem? What is your motor serial number? What is the fuel pressure at the rail?
  15. alldodge

    Slipping belt

    Use a metal straight edge to see if the face of the pulley's are aligned
  16. alldodge

    Vortec 350 5.7 Mercruiser Build

    Max rpms is dependent on internals used, and how those are balanced. Your cam list 1000-5000 rpms and I haven't seen where the pistons, rods, crank is anymore then stock. I would set it to 10*BTDC and see how it does. That said, your build may be an expert or just a good builder. See what he...
  17. alldodge

    Need More Bling

    Added some bling and I like it
  18. alldodge

    Possible short 7.4 Mercruiser

    Should not have 2 ALT's charging the same batteries all the time. Its ok to start and get things running, but once running they should be separated
  19. alldodge

    Possible short 7.4 Mercruiser

    Do both alts charge both bats at the same time or are they separated where each ALt charges only one bat? Should be each charge only one Most twin motors will be setup either one start and one house or two start and one house bat. One ALT will be used to change the house bat Is this a new to...
  20. alldodge

    Vortec 350 5.7 Mercruiser Build

    Looks good Assume you can get to the oil filter easy when installed
Top