Search results

  1. alldodge

    Kohler 7.5 EKD generator issues.

    What I'm saying is need to get some voltage readings. It could be its the circuit board, but no expert just spit balling
  2. alldodge

    1993 Mercruiser 3.0L I/O Concerns

    Lots of things, lost spark do to bad connection, key switch, kill switch, corrosion. Might be fuel, don't know there isn't enough info and no testing was done New to you boat means you need to check everything over and do all the maintenance to be more assured it will run
  3. alldodge

    water temp

    Don't know if the one from AZ is the same as the marine, but it might be. The North American is 240 ohms to 33 ohms (cold to hot). Take the sender and place in a pan of water and heat it up while reading the meter with a thermometer. See if it comes out the same
  4. alldodge

    Kohler 7.5 EKD generator issues.

    voltage limits exceeded None of the marine Gen manufactures have good drawings much less troubleshooting guides I'm seeing this error much like similar issues with Merc motors when the 5V is either higher or low then exactly 5V. In the drawing not there are other items connected with the O2...
  5. alldodge

    2016 H190 Aluminum to SS Prop question.

    Stainless props blades are thinner then aluminum so less drag, and they don't flex like aluminum does. If something is hit with stainless it can break the drive, but same hit with aluminum then it has a good chance to just be the prop. Current family load reaching 4000-4100 with 19, and going...
  6. alldodge

    Bravo 2 Speedo adapter at transom plate

    Looks like part of the quick connect for the power steering actuator https://www.mercruiserparts.com/bam/subassembly/30979/11210/200 Is a quick connect of some kind and there should be a ball bearing and end cap somewhere What is the serial number?
  7. alldodge

    1987 Starcraft 191 select trim switch

    If unable to figure out how to mount a different switch, then guess its time for another control. Might be able to find a used on craigs list. Or find someone parting out a boat
  8. alldodge

    Bennett Trim Repair And Auto Pro Install

    Today I tried to trim and the tab turns ON and doesn't turn OFF. So stop the motor, turn the battery switch OFF and it stops. Turn it back ON and its not running, so I'm leaving it alone Bennett never replied, so I called and got the same guy. Anyway, their sending me a entire new package...
  9. alldodge

    5.7L Black Scorpion running rough after warmed up

    Could also put a fuel pressure gauge on the fuel rail and see if its holding at 43 psi
  10. alldodge

    5.7L Black Scorpion running rough after warmed up

    Thinking its starving for gas. Being able to let it idle for a short time and run good again for a short, I would start with the gas tank vent. Could be the tank is drawing a vacuum because the vent is clogged, or partly clogged. When it does this remove the gas cap and listen for air being...
  11. alldodge

    2004 mercruiser 4.3 thunderbolt ignition

    This is for TBV but its the same for TB4
  12. alldodge

    Still running hot, please help .

    Tan wire temp gauge Tan/Blue alarm switch
  13. alldodge

    Still running hot, please help .

    The one with only one wire attached , Tan wire
  14. alldodge

    Still running hot, please help .

    Good, your overheat issue is fixed, now its a gauge/sender issue Check your sender with a ohm meter and pan of water
  15. alldodge

    PCM no spark! HELP

    I got nothing Guessing from first post: The ECM was fired somehow. You got another ECM but did not find out what fried the first one prior, so it fried the second I hope that is not the issue, but just guessing
  16. alldodge

    PCM no spark! HELP

    Dealer isn't a PCM dealer. I would normally say look to Rinda, but being this is a PCM 555 (and not a Merc PCM 555) it doesn't look like Rinda had anything to read it. Sorry to say, but I'm out of my league to help.
Top