Search results

  1. alldodge

    Bevel Prop Washer

    It is close, and it doesn't look like stainless but also don't see it rusting either
  2. alldodge

    4.3 MPI 2010 sn# 1A635910

    Should not have a full 5V on Blu/Blk Sensor is bad or wire has a break in connection
  3. alldodge

    4.3 MPI 2010 sn# 1A635910

    What software are you using, Diacom? Wires on your motor should be Blu/Blk Sense and Blk/Pnk Ground, the other wire should be Gray +5V Should se exactly 5V on the Gray wire
  4. alldodge

    Bevel Prop Washer

    I've looked at McMaster and was unable to find one that meets spec
  5. alldodge

    Bevel Prop Washer

    This is on my Verado's, note washer "d" orientation. Have discovered the industry seems to call them spring and conical washers
  6. alldodge

    Bevel Prop Washer

    Merc Flow Torque prop hub uses 3 washers and a self locking nut. The only one so far that isn't just a flat washer is the bevel (or conical) type. All dimensions are accurate except for maybe the Height. My caliper's jaw was not made so I could get to outer edge of each side. I should have layed...
  7. alldodge

    1998 2100 walkaround fuel guage location?

    Welcome I watched a vid of a open bow and didn't see the gauge but found a pic which one of them should be the gauge
  8. alldodge

    Maybe my turn for new boat time

    The older pre-2020 Chaps were better If I get another it will probably go back to Formula
  9. alldodge

    DeWalt corded drill DW106 Type-2 keyless chuck, bits slipping out?

    This was my Dad's, it's a Sears Robuck and Co Craftsman 60, just 3 amps and 425 RPM. It takes a few seconds to spin up and a bit longer to stop. Watched my Dad drill something on the patio as a kid and then get spun a 1/2 revolution before he could let it go Edit: not Craftsman
  10. alldodge

    Maybe my turn for new boat time

    In general no They look good, but there is a list of issues with the boat and have mentioned some of them prior. Even the deck gelcoat is poor, it has areas starting to show it's wearing through. My old 1994 Formula showed less wear than this one.
  11. alldodge

    Maybe my turn for new boat time

    No quality Craparral
  12. alldodge

    DeWalt corded drill DW106 Type-2 keyless chuck, bits slipping out?

    Hardly use my corded drills but almost every corded drill I have has more power than the cordless.
  13. alldodge

    Maybe my turn for new boat time

    Won't be long, would have already launched but life and the weather has gotten in the way
  14. alldodge

    Maybe my turn for new boat time

    Replaced Rev4 with Mirage Plus props today. Took me a bit to figure out how to swap the Tor-flow HD hubs, but got it done. Removed my props because I wanted to switch from the 19p Rev 4 to 21p Mirage plus hoping i could get some more reverse docking control. Note: See pic on how the washers...
  15. alldodge

    No dipstick on 1989 era 3.0L?

    scratch that
  16. alldodge

    Evinrude 7.5hp kill switch issue

    Welcome To kill the motor the Magneto needs to be grounded, should be Black/Yellow. Maybe a bad connection in the connector (coupler)
  17. alldodge

    DeWalt corded drill DW106 Type-2 keyless chuck, bits slipping out?

    3 sided bits https://www.homedepot.com/p/DEWALT-Black-and-Gold-Drill-Bit-Set-14-Piece-DWA1184/205952637?source=shoppingads&locale=en-US&fp=ggl
  18. alldodge

    Tilt ram piston removal

    Looks like tapered pins inserted and no way to pull them out Maybe @Scott Danforth or @Bt Doctur or @Texasmark
  19. alldodge

    Random

    Just picked up fresh 3.5lb of Atlantic salmon at 9.35lb at Meijer
  20. alldodge

    DeWalt corded drill DW106 Type-2 keyless chuck, bits slipping out?

    Could use 3 sided drill bit shanks
Top