Search results

  1. D

    1973 65hp Johnson

    does anyone have a wiring diagram for a 1973 65hp Johnson that they can post or copy a link to?
  2. D

    waterin bottom cylinder

    got a free outboard today, a 1975 20hp merc. I replaced the spark plugs and impeller, cleaned and rebuilt the carb and fuel pump. she starts and runs, but not very smooth and doesn't seem to reach full speed...kinda surges a bit at WOT. each cylinder has 110 psi, but I noticed that the bottom...
  3. D

    1971 60hp Johnson...rich/lean carb setting

    got a 1971 60hp Johnson 60173C. does anyone know how many turns out from lightly seated to set the rich/lean needle? this one starts and idles ok but produces a lot of white smoke.
  4. D

    220hp Laser warning horn beeps ...

    on my 1988 220 EFI Laser, when I first turn the key the horn does its test bleeps as it should and stops. then once I start it, its quiet for 2 minutes or so then starts bleeping again. she's not over heating, I have a temp gauge and its well under 140. the oil levels at both tanks are full, not...
  5. D

    1999 125hp merc quits...?

    I got a 1999 125ELPTO serial no. 0G911197 from an insurance claim. it had hit a reef and damaged the gearcase and trim unit. I got those replaced and took it out for a ride, it ran great but the tach didn't work. so I replaced the voltage regulator. the tach worked for a few minutes then stopped...
  6. D

    gasket question on merc 125hp

    when i bolt my 1999 merc 125hp powerhead,0G911197, back onto the midsection, do i need to use some kind of gasket sealer on the new gasket? it is a quicksilver/mercury gasket 27-43007 3. thanks, Don
  7. D

    question about warning horn...

    i have a 1995 Nitro, with a 125 Merc, it has a commander 3000 panel mount control. when i turn the key to "on" it does not give a test beep from the warning horn. i disconnected the tan/blue wire from the horn and connected a jumper to a ground and the horn sounded fine. anyone know this system...
  8. D

    whats the easiest way to tell...

    whats the easiest way to tell if you have a scored cylinder(s)? today as i was going across the lake, at about 3/4 throttle, my 1999 125hp merc slowed down like it was running out of gas. i shut it off to see what happened. still had gas, the overheat buzzer didn't buzz, i had good water...
  9. D

    another mercury tach question...

    my boat has a matching set of OMC gauges, for years i had a 1991 90hp Merc 2 stroke and everything worked fine. last week i upgraded to a 1999 125hp Merc 2 stroke and now the tach is not working right. sometimes not at all. does this newer motor require a different tach?
  10. D

    2 wire powertrim unit/3 wire powertrim unit interchangeable?

    i have a 1999 125hp Merc with a bad 2 wire power trim unit. this outboard has the 2 wire relay system. i have a 3 wire trim unit here and was wondering if it can be rigged to work with this system or do i have to switch all the electronics to the 3 wire solenoid system?
  11. D

    when do you need to get new rings installed?

    at what compression level are new rings suggested? i have a 1991 90hp that has 115# in all 3 cylinders. is it better to have them replaced before it gets too low?
  12. D

    V-6 gearcase pre-load pin

    what year did mercury switch drive shafts and get rid of the pre load pin on the v-6? will a preload pinned drive shaft work in a 1988 225 efi? can the pin be removed?
  13. D

    1986 6hp Evinrude driving me nutz!

    gotta 1986 6hp evinrude that starts right up, one or two pulls, idles down great, but will only reach full speed if you pull/push the primer knob. otherwise it will die out. I've gone through the carb and fuel system. new fuel pump, fuel lines and tank. Was told it has to be the primer unit, so...
  14. D

    1987 60hp Johnson warning buzzer

    I have a 1987 60hp Johnson, runs great, i did like what everyone says to do and disconnected the vro and i;m premixing the gas and oil. the problem is that the remote control still thinks its hooked up to the oil tank and that the oil level is low and starts buzzing a minute after i start it...
  15. D

    Converting a 6hp Evinrude into an 8hp?

    does anyone know if it's easy to convert a 1986 Evinrude 6hp, model E6RCDE, into an 8hp? I know they make kits to do this for a 9.9 into a 15...
  16. D

    rectifier? what does that do?

    what does the rectifier do? my 1994 merc 115, serial # 0G284446, has a 3 post recifier. can a bad one stop it from turning over?
  17. D

    1994 115hp won't turn over, sparks at battery

    got a 1994 115hp Merc. the power trim unit does not work. i tried pushing the up/down button several times times, the motor powers up but the ram is siezed. I removed the 3 wire trim unit completely. when i reconnected the motor to the battery, there were sparks at the battery. tried turning it...
  18. D

    how does the primer work on a 6hp evinrude

    got a 6hp evinrude that was made in Belgium. it has a primer knob instead of a choke lever. the primer seems to have 3 settings. how does this work and what are the settings? the motor will only run when the is pulled out to the first setting, once its running, if you push the knob in the engine...
  19. D

    different spark plug?

    what is the main difference between QL86C and QL77JC4 ? 6hp Johnson J6RICOB
  20. D

    100 to 1 oil mixture? really???

    just picked up a 1985 6hp Johnson that won't idle, the plugs turn wet and black. on the side of the cowl there is a 100/1 oil mix decal???? really? is this recommended still? i thought 50 to 1 was the norm. could this be the reason the plugs turn black and won't idle?
Top