Search results

  1. D

    Hub repair

    Oh really? Wonder were one could find a replacement hub? I pressed mine out,whole without tearing it
  2. D

    Hub repair

    Hey guy's,I'm wondering if anyone has tried or has fixed a spin hub ? I'd like to try to repair mine off my 25 hp Johnson,if so what types of adhesive would one use,and the prep steps,I can get a new propeller for around 80$ but thought I'd give this a whirl
  3. D

    No spark after magneto rebuild

    What do you mean by tucking wires away from the shaft? And frame meaning what?
  4. D

    No spark after magneto rebuild

    Hey all I've got a problem that I can't quite figure out never ran into this before my 69 9.5 I removed the magneto, new wires new coils new points new condensers and I have no spark whatsoever on either plug taking it back off went through it again still nothing I'm stumped, never had this...
  5. D

    Water pump not pumping enough water

    Well it was getting pretty warm before just spraying mist out of the discharge,before I changed the pump housing today I haven't had it back on the motor yet to test it I, tried it with my drill, I've seen guys on YouTube use the drill to spin the water pump and usually water sprays out of there...
  6. D

    Water pump not pumping enough water

    Okay I will try that in the next couple days hopefully that does the job
  7. D

    Water pump not pumping enough water

    Well I had the lower on the motor last week had it running and it was spraying out mist out of the discharge port so I took the lower back off tested it with my drill there was water coming out around the center of the pump housing with the drive shaft goes through and barely putting out any...
  8. D

    Water pump not pumping enough water

    No it's not I had the whole lower unit submerged except for the water tube grommet sticking out of the water
  9. D

    Water pump not pumping enough water

    O-ring at the top of the pump? I've never seen one that had an o-ring at the top of the pump I did replace the water tube Brahmin if that's what you're talking about all the water pump parts are brand new except the wear plate which looked fine
  10. D

    Water pump not pumping enough water

    The water pump housing is OEM the impeller is a knockoff I got from Amazon I've considered maybe that might be the problem but I use the same impeller in my 25 horse and it works fine
  11. D

    Water pump not pumping enough water

    I've had to lower unit off in my barrel with a drill on the drive shaft spinning it and it doesn't pump very much water the thermostat appears to be working there's no blockage in the powerhead I can pour water in the thermostat housing and it runs out through the bottom
  12. D

    Water pump not pumping enough water

    Yea it was but old and shot,not sure where the blockage would be all the passages seemed to be clear
  13. D

    Water pump not pumping enough water

    Hey guys I've got a question, my 67 Evinrude 18 horse is not pumping adequate enough water, have installed a new impeller a new pump housing and it still doesn't pump very much water out of there I'm kind of stumped as to why I sealed the pump housing down and the wear plate with sealer, never...
  14. D

    1967 Evinrude 18 HP

    Ok great! That helps narrow it down, never encountered not being able to find parts diagrams, thanks everyone!
  15. D

    1967 Evinrude 18 HP

    Just like part # for gear case ,just nice to be able to look up part# in case something breaks
  16. D

    1967 Evinrude 18 HP

    Hey all ,I'm trying to figure out why it's so hard to find part # for my 67 fastwin 18 HP, Marine engine has no listing for this motor, trying to find various parts # ,just picked this up today, usually don't have this issue
  17. D

    Putting a tiller handle on a mid 70's Evinrude 25hp

    There's the model number hopefully that'll help, wondering what the spread on tiller handle would fit? Like from 1960-1975? Horsepower from so to so ?
  18. D

    Putting a tiller handle on a mid 70's Evinrude 25hp

  19. D

    Putting a tiller handle on a mid 70's Evinrude 25hp

    Hey guys , wondering how hard it'd be to install a tiller handle on a 25 Evinrude,that has remote steering,do you have to change the stern bracket or? thinking of purchasing this said engine
  20. D

    9.5 issues

    Well problem solved,seemed to be my other fuel tank,, switched tanks runs well ,think my other fuel tank has water in the gas ,what a headache figuring it out 😳
Top