Search results

  1. CaneCutter79

    Really weird motor issue, trouble starting and motor sluggish

    My motor model # and type is listed below in my signature. I've had the motor rebuilt recently. This issue has been on-going since the rebuild. I've recently replaced the stator since my mechanic told me the left side of motor was weak but within tolerance (barely). I had hoped the new stator...
  2. CaneCutter79

    How to use DVA meter? I have a meter, not sure how to use it

    I have attached a photo of my DVA meter. I'm not sure how to use it and it didn't come with instructions (which would be great if it did). So stupid questions first.... - Where do I plug in the red lead for testing coils, CDI power packs, stator, etc.? Is it the upper right corner where it...
  3. CaneCutter79

    Outboard shakes - timing off?

    1979 Evinrude V4 85hp - Motor Break in Trials - YouTube My outboard has a case of the shakes. In the video above, you will see the outboard shaking slightly while idling. Then later as I rev the motor a little to show a quick throttle response, the outboard shakes even more. My main concern...
  4. CaneCutter79

    Thermostat bad or weak stator fouling plugs?

    During my rebuild, the stator readings were low on the left side of the motor. I was told they are within spec but on the weaker end. I have a new starter and I'm about 3-4hrs into my 10hr break-in using double oil. The old plugs are still in use and I'm going to get new at the end of break...
  5. CaneCutter79

    Gear lube and gasket material

    I will be changing my lower unit oil this weekend. My manual is old and references OMC "Hi Vis" lube. I doubt they make this still. I see there are ranges of lube on weights. What are advantages of one weight over another? Also, its not recommended to use synthetic for lower unit oil...
  6. CaneCutter79

    Lower unit oil/lube

    A) What color should lower unit oil be? Just drained mine and it was black as coal (green tint if rubbed to thin layer) and very thick consistency. B). What oil type do I use to refill C) I supposed to pump the oil in from the lower plug hole until the lube comes out of the top hole. D)...
  7. CaneCutter79

    Tachometer is not working

    1979 Evinrude V4 85hp (model 859995R) I have recentlyt rebuilt my motor. I just replaced the tachometer with a Quicksilver tachometer. Brand new, in box, (not used). I have tested the wiring for ignition source (12.67volts), ground (12.67), and sending unit source (about 4volts). SO the...
  8. CaneCutter79

    Break In Proceedures

    My Evinrude repair manual tells me to NOT use double oil for breaking in after a teardown or rebuild. This seems opposite of what everyone else typically says. I've used double oil for 12gallons and the plugs have fouled a little. Lots of carbon build up. I cleaned the plugs and put them...
  9. CaneCutter79

    OMC Bearing Assembly Removal Tool? Looking for this

    I have to pull my carrier bearing assembly to replace the bearing seal (part 0382408) for a 1979 85hp Evinrude (mo. 89995R). I was told there is a special OMC tool that is basically a big long rod with fine threads on the end. I was told I could make one but I'm not sure what diameter the...
  10. CaneCutter79

    Pressurization on old OMC Johnson/Evinrude Fuel Cans

    I'm questioning how these old cans work with pressurization and should they be vented when not connected to the fuel line? I only have one fuel line and I swap tanks when needed. I have some older 1979 6gal fuel cans and a couple of years ago, each can popped a pin hole in the bottom of each...
  11. CaneCutter79

    Trailer Bearing Repair 101

    First, I found and read the sticky at the top of the forum: http://forums.iboats.com/trailers-towing/re-wheel-bearing-sizes-294110.html I have a 2-wheel boat trailer (1979) with the original axle and the seals on the hubs need to be replaced. The wheels are also making a rubbing noise that is...
  12. CaneCutter79

    What's your favorite synthetic 2-cycle oil?

    1979 Evinrude 85hp V4 Mod. 85995R Motor is being completely rebuilt. All new pistons, new sleeve in #4 cylinder to factor bore. All cylinders will have factory bore settings with new rings, WEISCO pistons, new gasket kits, etc. All rebuilt by a certified mechanic. I'm considering using...
  13. CaneCutter79

    Just how difficult is it to rebuild an outboard?

    Re: Just how difficult is it to rebuild an outboard?
  14. CaneCutter79

    Just how difficult is it to rebuild an outboard?

    Re: Just how difficult is it to rebuild an outboard? Attached are images of the powerhead and parts
  15. CaneCutter79

    Connecting new trim gauge

    1979 Evinrude 85hp (Mod. #85995R) I am about to connect a new trim guage to my outboard. It's never had one before and I have two 16ga wires coming from the trim with factory connectors on the ends. One of the wires is for the gauge signal. I assume the other is ground? One side of the wires...
  16. CaneCutter79

    How much is an old Johnson Seahorse worth?

    I found this at an antique store. Asking $175 with original gas can and motor runs they say. I want this not actually use but to have as a collectors item. I really like the old outboards but I admit, I know nothing about them. I just appreciate where we have come from in the boating world...
  17. CaneCutter79

    1979 Evinrude - Main difference between 85hp and 115hp crossflow engines?

    Re: 1979 Evinrude - Main difference between 85hp and 115hp crossflow engines? So what does the filler block do and how would adding it add a few extra horses? Can you explain? This is really interestings. SO it appears I would need to change out the powerhead and lots of other things. I'm...
  18. CaneCutter79

    1979 Evinrude - Main difference between 85hp and 115hp crossflow engines?

    From what I can tell, these two outboards use the same powerhead. What's the main difference between these two motors? How does one get more hp than the other motor? Can any of you more experienced folks help?
  19. CaneCutter79

    Upsizing original wire guage for trolling motor

    I have a 1979 boat and the wire that is used for the original 25lb thrust trolling motor is about 12ga I believe. There are (4) 12ga wires running from the bow to the stern where the batteries are stored. The wires were once switched to go from 12v to 24v (not sure how that worked) but I have...
  20. CaneCutter79

    Safe to use indoor/outdoor carpet on boat/trailer?

    Lowes has some really cheap indoor/outdoor carpet that looks about what my current carpet looks like. This is for a 33yr old boat so I don't want a high quality carpet. Just something that will last a few more years. For $50 worth of carpet, seems like a good deal to me. The carpet is for...
Top