Search results

  1. C

    1999 115hp evinrude ficht

    I enjoy this hobby and just try to help out best I can while I learn as much as I can, not having spent my life in a outboard shop :-) other than my shed ! Had a few crow pies but it is part of learning. I hope landshark gets his 115hp FICHT going. I am trying to get a copy of the 115hp...
  2. C

    1999 115hp evinrude ficht

    not having the specs on the 1999 5psi seems....very low. the book on 70hp says minimum 34 psi so the 155hp should certainly have more than 5psi ... to pressurize try a few key on 3-4 and test fuel pressure. the lift pump can be simulated by hand pumping I doubt it is the issue...
  3. C

    1999 115hp evinrude ficht

    Oly'S brew is adding TCW3 oil at 200/1 mix in the fuel
  4. C

    1999 115hp evinrude ficht

    if you are talking DVA adapter you can build one your self for a few $ or search google. all it is is a AC rectifier/storage circuit to allow AC peaks to me measured as DC volts...
  5. C

    1999 115hp evinrude ficht

    The FICHT 2002 manual I have access to says 40v as the running voltage and on ETEC it was boosted to 55 v running 30 v key on. looks like your key on to running ratio is similar to more recent FICHT & ETEC Quite possible the 1999 version ran at lower volts . In any...
  6. C

    Checking Pts without Removing Flywheel CD-18

    as a member of AOMCI you would have download access to the Johnson 400 page + service manual which covers your oldy extensively. that is where that above page comes from :) that book is a bible for oldies maintenance carbs, ignition ph gc etc....
  7. C

    Checking Pts without Removing Flywheel CD-18

    just adjustt the points to a max of .020 at the highest point of openning but.... if never done you should pull the FW inspect for cracked coils possibly replace condensers etc... caraefull with the carbon seal under the PH... very delicate
  8. C

    Do you make your own gaskets ?

    can't see why not .. no heat or much pressure in the carb. but carb kits come with them and not verry $$$$
  9. C

    1999 115hp evinrude ficht

    https://www.etecownersgroup.com/post/hp-fuel-pump-screen-9654752?highlight=high%20pressure%20pump%20screen
  10. C

    1999 115hp evinrude ficht

    btw... check the VST ...your FICHT it likely has a small conical filter on the return manifold fuel supply from the injectors. it can block/impair fuel flow causing inj. issues ....incl cooling if fuel doe not flow Even on the 2005 ETEC books they don't show it !!! CAREFULLY remove the...
  11. C

    1999 115hp evinrude ficht

    yes the ETEC inj. in the video are different from FICHT . The video was to show the basics of inj. cleaning you are aware that changing injectors requires injector data spec updates to be loaded in the in the EMM otherwise engine damage will most likley happen at higher RPMs here is a...
  12. C

    1999 115hp evinrude ficht

  13. C

    1999 115hp evinrude ficht

    comp ok sparks OK ... now you need fuel the best way to know if the injectors are spitting gas is to remove a plug ground the plug properly and insert a paper strip inside the cyl. if it does not get wet with fuel the injector is/are not spitting fuel in the cyl and the engine will...
  14. C

    90 Etec tilt and trim pump leak

    Do let us know how it all works out :-)
  15. C

    Do you make your own gaskets ?

    I have made some where pressure and heat is not a critical issue ex: impeller base gasket , intake manifold etc... Cyl heads = OEM !!
  16. C

    What do I do??

    try used parts places like Tim'S outboard or Doug Pen or go to AOMCI classifieds...
  17. C

    90 Etec tilt and trim pump leak

    do you have the manual ...some seals differ check in at the ETEC user board to confirm part# https://www.etecownersgroup.com/?forum=136483 btw check oil type for ETEC T&T book says to use a special Evinrude T&T bio oil $$$$$ vs common mineral stuff $$ after much...
  18. C

    1971 Evinrude fisherman, not pumping water

    if never done.. a reseal job can be a challenge I woud do a pressure test if you can (used soapy water spray) to see if you have bad seals. otherwise new nylon washers may... solve the problem check the small shifter (phipps) screw for leaks on my last reseal of a 5.5 I used...
  19. C

    1976-1978?? 9.9 flywheel nut

    if you do go hardware store at least l get a nut with nylon locking head to hold it down !
  20. C

    Evinrude 9.5 vs 8hp speed test

    something in me was left over.... from my early days of boating in the late 60s
Top