Search results

  1. C

    1980 j25rcsa solenoid issue

    selenoids are just electrical magnets... aside from the large posts to feed battery +12 the starter the inner coil needs a ground (direct or via safety devices to protect you) and... +12v from the start key position.... so your diagram is OK if the new selenoid does not "click" it...
  2. C

    Johnson CD-12

    oily tank water is from unburnt fuel and oil you may have to pull the cyl head and resurface on 120 grit paper over a plate glass or large ceramic tile until you see bare metal all over.. regasket and torque to spec... retorque after a few hours great motors btw run at 24/1
  3. C

    Johnson CD-12

    see pict btw you did install the impeller key ....
  4. C

    propeller seal removal

    (735) Pressure testing an outboard gearbox - YouTube I purchased that red pump on amazon and it worked fine testing my ETEC 75hp gearcase. The $12 oil bottle pump kit provided the OMC adapter I needed . you can test pressure and vacum with it.
  5. C

    Possible kill switch problem

    I agree also but eventually some of that " to hot" water should come out to influence the pee stream temp depending on the thermostat design no?
  6. C

    Possible kill switch problem

    are you saying an overheated engine will not influence the outgoing temp ?
  7. C

    Possible kill switch problem

    anything is possible but such timely shut downs would probably be related to heat generation affecting..something involved with the ignition even a new pack can get hot ! Do you have a pee stream have you tried testing the pee stream .. is it HOT or warm when it dies ? can you scan...
  8. C

    1999 50hp Johnson 2 stroke won’t start

    Lucst if you want to arrive at a conclusion no need to repeat the same actions or trow parts at it... you must proceed methodically... and if we can help great but specific questions to you must result in specific answers to progress to happiness :-) Q-do you or do you not see +12v...
  9. C

    1999 50hp Johnson 2 stroke won’t start

    perspective surely :)
  10. C

    1999 50hp Johnson 2 stroke won’t start

    and btw... when you push/start and you hear a click .... does it click when you push ====> choke does it click when you turn to START...=====> selenoid which click do you hear or feel
  11. C

    1999 50hp Johnson 2 stroke won’t start

    bottom connector on the selenoid looks corroded and loose crimped... did you inspect/clean it or is this a photo "before" possible 1999 Johnson BJ50RLEEA 50hp looks like yours but sevral models exist if you can locate the fat side connector plug ..open it clean all contact points...
  12. C

    1999 50hp Johnson 2 stroke won’t start

    I looked up the parts diag. for a 99 50hp ...you seem to have a engine control module ?? do you? ...if so anythig goes ... you will need a wiring diagram and expert opinions going further .... . post your engine model# !!
  13. C

    1999 50hp Johnson 2 stroke won’t start

    enough parts will solve your problem but the art of diagnostics is there to save you money. test results dictate the solution otherwise you are in for more expensive & needless parts buying. . go to your +7v test point and work backwards till you find +12 btw if you apply a good...
  14. C

    1999 50hp Johnson 2 stroke won’t start

    7v indicates a resistive path check the voltage value at the key S position on the wire heading back to the selenoid if it also reads 7v check the input voltage to the switch on the B+ post it should be 12v if not work backwards to the engine ... have a buddy operate...
  15. C

    1999 50hp Johnson 2 stroke won’t start

    "Turn the key and hear click at the solenoid and starter moves a bit...Jumped starter and it works" fuel, carb and choking aside these symptoms kind of points to poor connections or poor cables simplest thing to do for now is to clean up (polish) all connections related to the battery...
  16. C

    1979 85hp Prop Shaft Oil Leaks and Skeg Repair On Johnson Evinrude

    pretty bad cracks... if you ever "touch" a rock or obstacle the whole lower part could "fall away" :-( Surface patching may seal it but it will always be weak ...at the very least maybe a good welding shop can help a donor part maybe... have you enquired about it ?
  17. C

    94 Johnson 120hp no spark

    nothing like new parts.... but$$$$ wise can you pull or position this wire and JB weld it to keep it from ever moving again ....? bring a kicker :-)
  18. C

    1972 65HP Johnson wire issues

    anything goes if you can't splice in new wires,,,, liquid tape, vinyl tape, (heat shrink involves cutting inserting soldering...then heat shrinking) you can "paint" the wires with common silicone sealant, I have used contact glues to seal and solidify cracked insulation. Some glues...
  19. C

    1997 Evinrude 4hp tuning help

    if fuel reaches the carb it will work but you have to figure the fuel flow from tank to pump and pump to carb inlet
  20. C

    burnt oil leak

    could t be just carbon crud, unburnt fuel mixing and drooling out if gearcase oil is ok just keep any drains clear and open
Top