Search results

  1. jimmbo

    Sputtering Johnson V4 90hp - 1994

    Looking at it again, maybe it looks like a Decanter for Wine...
  2. jimmbo

    Should I change prop pitch/ go to stainless.

    Depends what you think is 'Improved Performance'. My first experience with a SS was in 1985, when I replaced the Al Prop on my I6 115. Both Mercury Props, no increase in Top Speed, but a much better Grip on the Water, it not longer lost its Bite in turns when trimmed out, and could lift the Bow...
  3. jimmbo

    1976 Evinrude 9.9

    Here is one of the Videos on YouTube showing a Pump like yours, maybe you've seen it, but it does point out a couple of tricky spots that could cause problems
  4. jimmbo

    Should I change prop pitch/ go to stainless.

    ROTFLMAO!!! My experience with Rocks and SS Props. Bent the Propshaft too. Impact occurred at about 21mph
  5. jimmbo

    Should I change prop pitch/ go to stainless.

    The pic of 15" shows it to be a Stainless. As for the 17" being Standard. It is the Pitch that is shipped with the Engine. It was picked by the Manufacturer, as being suitable for the expected Boats the Engine most likely to be installed on. In the Evinrude-Johnson Engine Brochures, it was...
  6. jimmbo

    Water Pressure gauge installation, need a little help!

    I suspect the Instructions are referring to a Mercury, as they almost always had a Place, with a Brass Plug where a Pressure Gauge Hose/Tube could be fitted
  7. jimmbo

    Dumb question

    It probably had a Pinch Band type Clamp on it from the Factory. I'm surprised the Hose hasn't popped off.
  8. jimmbo

    HELP - Mercury Motor Won’t Start - Carburetor is suspect

    Welcome to iboats How did you come to the Conclusion that this is Mercury? It is an OMC Motor(Evinrude/Johnson) What are the Compression Numbers? Is the Spark strong enough to jump a 3/8" Gap? Is there any Blockage in the Fuel System? Carb Circuits could be gummed up with Dirt, Gum, and...
  9. jimmbo

    115 6c TOP piston cylinder issue

    Even though, in theory the Rings should fit, the Piston Rings Gaps should be checked and Adjusted to each and every Cylinder Bore. A lot of Machine Shops will require the Intended Pistons be supplied to them with the Block, so they can be measured(even brand new Parts can vary slightly in size)...
  10. jimmbo

    Should I change prop pitch/ go to stainless.

    It is your Motor and you are free to downgrade your Boat's Performance with that stuff.
  11. jimmbo

    Sputtering Johnson V4 90hp - 1994

    You said in the Original Post that your last Experience was with SBC. Forget most of what you know about the Chevy, in fact any Car/Truck Engine, as these 2 Strokes are quite different, when it comes to Adjusting. First Things first, have you done a Compression Test? If No, do one and post the...
  12. jimmbo

    Should I change prop pitch/ go to stainless.

    That big white piece of Garbage bolted to the AV Plate is Not Standard on any OMC Motor. Whatever that thing bolted to the Skeg is, is certainly going to slow you Down, I suspect the 15" is gonna be close to what you need to run. WOT Range for your Motor is 4500 - 5500. That Motor is making...
  13. jimmbo

    115 6c TOP piston cylinder issue

    600-650rpm, in Forward was the Idle Speed Spec for those engines. I used to adjust them for 575-625, just to lower the Shock imposed on the Driveline when put into Gear. Regarding your Piston Rings. You are checking their End Gaps in their assigned Cylinder at several spots, and adjusting if...
  14. jimmbo

    Sputtering Johnson V4 90hp - 1994

    If you are referring to the Milk Bottle shaped Opening not being covered by the Gasket, it would be a Waste of Paper, as there is nothing on the Manifold to contact
  15. jimmbo

    199?? 40hp force year question

    Kiekhaefer, never built any Force Outboards. Kiekhaefer's name never appeared on any Brunswick made Outboard after 1972.
  16. jimmbo

    Just thought I'd share a nice photo.

    But you didn't, so I did
  17. jimmbo

    Which plug for a 1985 Force Chrysler 50 HP?

    Champion UL81C NGK B7HS Gap 0.030"
  18. jimmbo

    Should I change prop pitch/ go to stainless.

    First of all, do you have any info regarding what you maximum Rpm is with the 17 inch prop? Also do you have the rpm without all that Garbage bolted to the Gearcase? I have Never heard of a Steel Prop for that Engine, only AL and SS. Not all SS is non-magnetic
  19. jimmbo

    engine cowel

    A few pics would help
  20. jimmbo

    throttle cable and idle adjustment 1986 Mercury 35 hp 2-stroke

    By having the Sense to adjust the length of the Throttle Cable as you were trying to lower the Idle Speed, to me, indicates you have the Capability to understand how these Motors work. There needs to be a bit of Preload on that Cable once the Idle Speed is set. Too little and the Idle Speed may...
Top