Search results

  1. Berdink

    Linkage Slop

    1994 Johnson 90hp v4 Crossflow. . The throttle Linkage has about 1/4 to 3/8 play. See video. It might be hard to see it, but the plastic outer piece that I'm pushing and pulling allows the inner piece to slide in and out about 1/4 to 3/8. . Is this normal? It makes quite a difference in idle...
  2. Berdink

    Temperature Switch OMC p/n 0386686 Test

    Thanks for letting us know how you tested it and your results.
  3. Berdink

    Sputtering Johnson V4 90hp - 1994

    How about a girl with kaleidoscope eyes?
  4. Berdink

    Sputtering Johnson V4 90hp - 1994

    I have this in my cart: https://a.co/d/0b11TYAP
  5. Berdink

    Sputtering Johnson V4 90hp - 1994

    I need to get a tach. It felt like it never completely wound up. It ran really smooth, but it sounded like it still had more it could go. Not that it felt struggling at all, just that it still had more to give.
  6. Berdink

    Sputtering Johnson V4 90hp - 1994

    All good. Got up to about 33mph
  7. Berdink

    Water Leaking Near Exhaust Plate - V4

    I just finished watching a video on it, and my 90 just takes two of the same gasket.
  8. Berdink

    V4 - Minimize Chances of Broken Rings

    Ha! 😆
  9. Berdink

    V4 - Minimize Chances of Broken Rings

    For a 90hp V4 Crossflow the stock prop is a 3-blade aluminum prop with a 13-inch to 13-3/4-inch diameter and a 17-inch or 19-inch pitch. . The one I have now is 17 inch. Going to 15 inch on my 90hp V4 Crossflow would put less load on the engine, correct?
  10. Berdink

    V4 - Minimize Chances of Broken Rings

    I It looks like BRP (Johnson/Evinrude) 2-cycle oil is now owned by XPS. I hope they don't start trying to maximize profits.
  11. Berdink

    Sputtering Johnson V4 90hp - 1994

    I need to apologize. It may have been the sync of the carburetors. I had ordered those two rollers that were missing - the one in the c shaped slot, and the one on carburetor that should align with the mark. . As so, I had to readjust the linkage. . I think I was off even before because I...
  12. Berdink

    V4 - Minimize Chances of Broken Rings

    I've been watching outboarddad on YouTube because he has a lot of 'How To' content on Johnson's 70hp and V4's. When he has a rebuild, he asks what oil they were using. He said the overwhelming biggest majority of rebuilds is ones that use a lower quality oil. He says stick with manufacturer's...
  13. Berdink

    1981 Johnson 90 HP overheating, but not all the time

    I've been searching for a MacGyver hack where you mount a digital thermometer with a cable to the dash. You mount one sensor on each side on the top cylinders.
  14. Berdink

    Sputtering Johnson V4 90hp - 1994

    Thanks to all for helping me through this. I had a trip planned and I was pushing to find a good running replacement for my 84 Suzuki.
  15. Berdink

    Water Leaking Near Exhaust Plate - V4

    When I rev it up, water sprays from behind the exhaust plate. See pictures. It's also coming out around some of the screws, and appears to be a gasket issue. . Is this gasket a big deal to replace? .
  16. Berdink

    Sputtering Johnson V4 90hp - 1994

    . .
  17. Berdink

    Sputtering Johnson V4 90hp - 1994

    Okay! I think I, (you guys got it). I now just need to take it to the river and run it around some. . It sounds nice and idles down low nicely. . I will upload some videos later tonight and post the links to them here. . It may or may not be it, but I disconnected the primer solenoid. Even...
  18. Berdink

    Sputtering Johnson V4 90hp - 1994

    Moving on to the bleed system (recirculating system and valves). Looks like I get to take the carburetors off again. 😊
  19. Berdink

    Sputtering Johnson V4 90hp - 1994

    @racerone, I saw you post in another thread about a way to check if the crankcase isn't sucking in unmetered air. I did a search on that and I guess one suggestion was to remove the carburetors and put a seal plate over the intake manifold. Then I think you somehow plug off exhaust openings too...
  20. Berdink

    Sputtering Johnson V4 90hp - 1994

    Ha! I googled it. The bleed system appears to be the Recirculation System. I was just reading about that last night. I think it was a suggestion by Joe Reeves. . See, I'm learning.😊 See, I'm trying. 😊
Top