Search results

  1. toddschubert

    Can't find problem.....stumped!

    I have looked and looked but but I can't seem to find a problem with my 88spl '92. I run it and run it. Runs all day and runs all night! Starts on second turn of key and a bump of the primer. Plugs are clean and wet, wires look good, timing perfect and carbs are clean as a whistle. My boat...
  2. toddschubert

    Larson 15 bow rider with rotten stringers bc they weren't glassed over. Factory help?

    I have a second hand 93' Larson 15 All American run about bow rider that the stringers and subsequently the floor are/is rotting out. The factory had not put any fiberglass reinforcement up and around the stringers. Just a little matte up part of the sides. The stringers are constructed using...
  3. toddschubert

    wireing a burned up regulator on an 89 88 spl please read

    Re: wireing a burned up regulator on an 89 88 spl please read
  4. toddschubert

    what the heck again!!! 1992 88 spcl. won't start. no spark. did I blow power pack?

    I changed plugs yesterday and started her up. Ran fine I launched today and it won't start. I get home and investigate to find I have no spark on all 4. What is a quick way to check Power pack and what else should I look for. Seloc manual not much help...Damn thing!
  5. toddschubert

    What the heck?!? Is champion failing me? Spark plug conductor corroded

    Re: What the heck?!? Is champion failing me? Spark plug conductor corroded Now here is the pic. File was too big before
  6. toddschubert

    What the heck?!? Is champion failing me? Spark plug conductor corroded

    I accidentally broke the tip off a spark plug durring routine check and found the core of the plug was corroded through the length of the pin. How is this allowed to happen? No cracks were found in ceramic.
  7. toddschubert

    88 spl putting out 16 volts at 2000 rpm. 2 high? im afraid of frying accesories

    My volt meter reads up to 16 v while running but only sometimes. The gauge works fine with testing. I feel this is a rectifier problem. Sound right?
  8. toddschubert

    Have 290 SeaRay w twin MERC That have corrosion prob. How to trouble shoot mercathod

    I'm from the Johnsonrude forum but I'm helping a friend w 290 Sea Ray that has badly corroded od's. We are pulling them today to further inspect. Could someone briefly explain the mercathode system and how to trouble shoot if it is working properly? Owner thinks neighbors boat is putting...
  9. toddschubert

    I am needing to replace the od's on 290 SeaRay..corrosion/anode problem. Need assist

    Hi guys I'm a Johnsonrude guy who has just been handed a 290 SeaRay with Merc outdrives with severe corrosion damage. The hydraulics are shot meaning the line connection are deCentigraded . My first time dealing w/ such and was looking for a little help. Merc od model number not avail but s/n...
  10. toddschubert

    Decarbing 88spl getting mixed advice on how long to let soak...using Seafoam to do it

    I hear anywhere from 4 hours to overnight on decarb process. Any input on this? Also anybody see a problem using Seafoam? I have found it to be a wonderful product that saved me a carb. teardown just running it through fuel.
  11. toddschubert

    Grease or no grease on spark plug wires at coils (88spl)

    I have remnants of what looks like old dielectric grease on spark wires at coils. At first I just thought that was a good thing but now I wonder. PO must have put it on but not at spark plug. I'm thinking I need to clean it up and go bare. Any input on this matter?
  12. toddschubert

    '93 88spl stopped chging battery. Used to read 16 volts wot now only 12

    I am not the big electrical guy on the block and to be honest I havent even started looking for problem. I was hoping I could get some clues as to what to look for first. I've got the tools and equipment to test everything. Any input? My master fuse panel is very difficult to access so I am...
  13. toddschubert

    install a temp guage

    Re: install a temp guage A contact sending unit just touches the metal and therefore the temperature of the water inside. No need to drill aANYTHING. if you place it in mast normal cases like on a head use a z bracket that will come w sensor kit. I have same motor. If you do the above you...
  14. toddschubert

    still having prob with loosing power when hitting wave on 88 spl

    I've gone through all wiring, gooped up coils, and can't. Figure why I can sometimes run at5500 then hit a bump and drops to 4500 where it stays most of the time. Usually not a problem cuz I have to maximize fuel to get to camp and back so I only run at 3000 / 20 MPH Any ideas?
  15. toddschubert

    88 spl sometimes gets a surge but if i hit a wave it backs down timing arm loose

    The bushing on the throttle can seems loose. The timing arm moves enough to advance it by hand. Could that bushing allow this to happen? Its a cheap part...just asking.
  16. toddschubert

    88 spl putting out 16 volts at 2000 rpm. 2 high? im afraid of frying accesories

    Hey guys, 93 88 spl is putting out 16+ volts starting at around 2000 rpm. Has been since purchase from PO last year. I figured guage was a little off but finally got around to putting good meter on bat while running at 2k. should this be a concern? Is rectumfryer bad? I just put new gps...
  17. toddschubert

    Want to put single thermostat sensor on '93 88spl. Would thermo housing be good?

    Re: Want to put single thermostat sensor on '93 88spl. Would thermo housing be good?
  18. toddschubert

    Want to put single thermostat sensor on '93 88spl. Would thermo housing be good?

    Re: Want to put single thermostat sensor on '93 88spl. Would thermo housing be good?
  19. toddschubert

    88spl has ticking sound like arcing at lower RPMs but stops if I adv. throttle a bit

    '93 88spl starts to tick like it is arcing somewhere but stops if I advance throttle just enough to change timing rod but not fuel flow. Does it around 2000 rpm. Also used to run 5500 rpm wot and now only 4500. Sometimes it clears up and hits 5500 but when it was doing this and I hit a wake it...
  20. toddschubert

    Want to put single thermostat sensor on '93 88spl. Would thermo housing be good?

    Re: Want to put single thermostat sensor on '93 88spl. Would thermo housing be good? This is what I came up with that is non intrusive and will give an average temp reading from both cyl banks.
Top