Search results

  1. alldodge

    1998 Merc 3.0l Front Engine mounting.

    Yes.... With drive removed, insert alignment bar into coupler and check. It should go full in and out using no more then 2 fingers
  2. alldodge

    Blower fan and Bilge is NOT working. Help

    Being a bilge pump and not a blower, look at the specs of the pump you just installed. Should be no more then 10 but probably 7 or so
  3. alldodge

    1977 18’2” BeachCraft Mercruiser 888 302Ford

    You will be able to get internal parts for the 302, others may be a wild card This is the parts breakdown https://www.mercruiserparts.com/888-2-bbl-ford-302-v-8-1971-1977-31 Suggest looking real close and the stringers and transom. My guess is they need work and will cost plenty
  4. alldodge

    Mercruiser 5.0 dies while idling - no fuel from line

    Possibility but also could be the float needs adjusted Is it dripping?
  5. alldodge

    Blower fan and Bilge is NOT working. Help

    Might also be the switch. Use a meter to see if 12V is present
  6. alldodge

    Ease of towing larger boat

    Sure hope were not getting into the 26T rating for cdl
  7. alldodge

    2006 Chaparral 190SSi Mercruiser 5.0 has perplexing alarm/power loss

    Verified it is TBV (Part number on port side elbow) but do not see knock sensor mounted. Don't think the motor has one installed The boat gauge is off because IR measuring 120* on thermostat housing and gauge shows 170*. Measure temp at the temp sender and not on top of the housing Not good...
  8. alldodge

    Alarm Going Off for Mercruiser 350 Mag MPI

    Glad your fixed but 5.5 hours to replace is a bit much. Doesn't take me that long and I have to hank upside down to get
  9. alldodge

    Koehler generator

    See pdf page 32 or manual page 3-4 http://www.30plus.org/Chief_Plasma/Kohler-TP-5695.pdf
  10. alldodge

    Koehler generator

    Depends if its gas or diesel and what Temp it will be used in. Model number would help. For the most part its 10w30 or 10w40 which gives a Temp range from -4* to 100*F for gas.
  11. alldodge

    '85 Oildyne Trim Pump Reservoir - Can I switch from metal to plastic?

    Was just looking at the Oildyne new style manual and Merc manual 4 for old style. The old uses several screws which hold the bottom plate on, the new uses one in the bottom center The old pump motor appears to use more screws to hold in on the top then the new In short I don't know
  12. alldodge

    Volvo Penta DP-S Parts Diagram?

    If your looking for parts breakdown https://www.volvopentashop.com/epc/en-US If your wanting a manual, suggest VP
  13. alldodge

    More U-joint knocking?

    If you notice/feel any play in the U joints they need to be replaced Gimbal should feel smooth as silk when turned with your fingers
  14. alldodge

    Mercruiser 5.0 dies while idling - no fuel from line

    Look inside the bowl if you see the carb dripping. My guess it is dripping, and then need to find out is it the needle, incorrect float setting or float is to heavy
  15. alldodge

    Hunting

    Not a big hunter mostly because Admiral doesn't want me to kill Bambi. She probably won't mind the day after one hits her car :unsure: Bought some more rounds last year to get one, and didn't even go check the sightings. Anyway I'll stop winning and back to your question. Doesn't matter if...
  16. alldodge

    Mercruiser 5.0 dies while idling - no fuel from line

    ok, the carb is flooding the motor.
  17. alldodge

    RPM falling back or motor stops

    This should help https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&ved=2ahUKEwjv4d7i3c7yAhUbRjABHUhJD-gQFnoECCQQAQ&url=http%3A%2F%2Fengine-manual.com%2Fen%2Findex.php%3Fcontroller%3Dattachment%26id_attachment%3D135&usg=AOvVaw389rInABUISq7vvrp3hv66 I found it by searching volvo...
  18. alldodge

    V/P 5.7 GI-D not reaching above 3400 rpm

    Thinking the motor might need a valve job with your compression numbers. A new motor would be 150 so with seeing 180 the gauge is probably off. If we reset the 180 to 150 which puts the 150 at 120. In any case there lowest should be no more then 10% from the highest Before pulling heads it...
  19. alldodge

    Mercruiser 5.0 dies while idling - no fuel from line

    Fuel pressure is good but fuel line is dry when motor is shut off when warm. The antisiphon valve is working and fuel is not draining back. If the above statement is true, then its either the pump or the rubber fuel line is collapsing inside
  20. alldodge

    Can someone identify my control?

    This is the area with all the controls https://www.mercruiserparts.com/remote-controls-and-components-1986-th and this looks like it https://www.mercruiserparts.com/bam/subassembly/32078/1989/50
Top