Search results

  1. C

    Question for "the machinist"

    11 years later....?
  2. C

    Evinrude E-TEC 150. 2008 software

    BTW Diagnostic sw is great information provider and handy for testing things but could cause issues . remember the old saying.. if it works don't fix it :-) If it fires up good runs good it is probably good so just pamper it with 2+4D, carbon guard EV engine cleaner etc... new...
  3. C

    Evinrude E-TEC 150. 2008 software

    you should visit the ETEC user board for articles such as these and expert help on ETEC issues https://docs.google.com/document/d/16BAQLd2i43h30MTOuWJ0-T6_DO9wX5yK5MzOOunwzUk/edit did you install the updates and driver files for the FDTI interface and the USB com port to the triangular...
  4. C

    6 hp 4 stroke won’t run when connected to external tank!

    inlet needle should stop the inflow of excess gas ... manually pumped or fuel pumped try taking the cap off vents get plugged sometimes
  5. C

    How do I get Johnson 88 motor up trim switch not working

    How or did you confirm the problem is limited to the switch itself ?? any fuses to check ? poor connections .. faulty relay faulty trim motor weak battery ? etc...
  6. C

    6 hp 4 stroke won’t run when connected to external tank!

    try openning the fuel cap on the tank to ensure proper venting and keep any tank pressure build up from pushing to much fuel to the engine and overriding the inlet needle and flooding the carb .
  7. C

    Pitot nipple on lower case. Evinrude 90hp e-etc

    you can also ask the folks on the ETEC board in the I3 sub section https://www.etecownersgroup.com/?forum=136483
  8. C

    Johnson 9.5 Weak Spark

    don' t forget that 9.5hp pull starters don't spin the fw very fast and resulting sparks may appear a bit weak yet after starting they run fine. you should be able to screw in the wires on the coil pins at least 3/8 inches cover with the little boots or insert di-electric grease in...
  9. C

    Johnson 9.5 Weak Spark

    I have fixed up several and I can't say any generated real hot blue .5 inch sparks... that said for 50-60 year old engines remove the mag plate to properly "screw in" the plug wires on the coils replace the coil wires anyway with 7mm metallic core wires. I use automotive Belden wires...
  10. C

    Only Running on One Cylinder

    ok not firing... but do plugs seem wet with unburnt fuel ?? if not..... fuel is not reaching the cyl. you need to find out why . stuck reeds ?? dirty/plugged carb ??
  11. C

    1950 Evinrude 7.5 hp, Model 4434

    https://forums.iboats.com/threads/evinrude-model-4434.106922/
  12. C

    No power to tilt and trim relays.

    ?? it is fixed yes no ? So I have power at the relays now. And I check the tilt and trim motor and they work
  13. C

    No power to tilt and trim relays.

    bat and grd are like ying and yang...
  14. C

    Is it worth the work 66 Evinrude 15hp

    WELL... the 15 is a good engine and lots of folks bring them back alive. 2 coils are likely shot (cracked) they are 15$ each the rest maybe just a good clean of the points set at .020 Condensers may be bad also...
  15. C

    No power to tilt and trim relays.

    normally +12 is taken of the selenoid +12 from the "battery side" post and then FUSED before distribution depending on the T&T model it may have 2 wires to the motor or 3 wires which either directly feed the motor and use a common ground wire ...or with 2 wires the polarity is...
  16. C

    No power to tilt and trim relays.

    check for any fuses ...? all connections secured, shiny.
  17. C

    Oil Injection Kit?

    didn't Mercury have an auto-blend oiler box which should work ??
  18. C

    2001 115hp Evinrude Ficht alarm but no code

    sorry for my english does "going off" mean "came on" or turned off I gave it full throttle and she got on plane, alarm and light went off again CAME ON ??) . Reduced throttle and they went off. ( went dark)
  19. C

    Johnson JW-10 value help?

    I never paid over 60$ for a JW .. one was $40
Top