Search results

  1. nola mike

    1986 Alpha One has leaked oil since service....

    If then. They're a real PITA on the gen 1's.
  2. nola mike

    Swap carby on Mercruiser 1986 inline 6 to holley carby

    There was no inline 6 in 1986... Anything's possible. But why do you want to switch, what are you switching from...
  3. nola mike

    4.3l Merc cruiser

    Don't turn it by the crank bolt.
  4. nola mike

    4.3l Merc cruiser

    Well... Many possible things to check. First, you need to assume that nothing has ever been done to the boat. There's a ton of maintenance that you should do before taking it on the water. As for not turning over--first thing I'd do is pull the plugs and see if you can turn it by hand (not using...
  5. nola mike

    1989 vs 2008 4.3 differences

    I'll check out my setup when I get back to the boat, but also remembered that you need a new throttle bracket if you're going from a 2bbl carb to a 4 bbl
  6. nola mike

    Does this oil look bad to you? (white smoke coming out of breather tube)

    That oil looks brand new. Water probably won't show on the dipstick. I'd run it a bit to see what happens. More smoke? Oil level gets higher? Noises? Smoke with increased temp can be a lot of things getting hot that shouldn't be
  7. nola mike

    Engine failure?

    Dunno if this has been suggested, but pull the plugs.
  8. nola mike

    Formula 26 PC - Not seized engine! Seized outdrive?

    Because that is literally why that bearing exists. Don't overthink it.
  9. nola mike

    1989 vs 2008 4.3 differences

    Is this for the cannon plug connector and circuit breaker?
  10. nola mike

    Mercruiser Alpha 1 Gen 1 Project

    Not all the A1G1 drives need the rolling torque method when reassembling the bearing pack...If his is an '85 or so he may have the old style assembly.
  11. nola mike

    What is this gel-like substance in my carb? Mercruiser 3.0L Alpha 1

    No, e10 has been fine for decades. My '86 says it's fine to use. Old gas will turn into varnish and gel up. Doesn't sound like you had it in there long enough, but that looks like the result.
  12. nola mike

    Base Timing Mode

    Tb iv doesn't use base timing mode. You probably have tb v given the year, but 🤷
  13. nola mike

    no spark Mercruiser 120

    Idk what the limit for continuity is on your meter. I wouldn't use it that way. Like I said, 200k sounds high. Swap in a good wire and plug if not a tester into your coil. It sounds like your points are closing and making a connection
  14. nola mike

    no spark Mercruiser 120

    That does sound high. What's your reading at the coil neg with the points closed? Did you try putting a spark plug tester directly on the coil?
  15. nola mike

    Formula 26 PC - Not seized engine! Seized outdrive?

    Like Rick said, don't do that Yes, you may have bent some shifting components getting it off. Yes/no Not normal. Should spin in both directions Yes, I blew an outdrive the way during my first season of boating. There's a pressure relief passage in the transom plate connecting it to the...
  16. nola mike

    2008 3.0L AlphaOne no water to engine

    Leak test it before you take it back apart to see where that waters getting in
  17. nola mike

    1989 vs 2008 4.3 differences

    My mistake,I thought you were bringing the old oil tube over. You already have the correct one on there. Yes, like Scott said bending the tube if possible would be the cleaner solution, but cutting both should be ok as well. Obviously you'd need to scribe some new marks on the bottom of the...
  18. nola mike

    Needing Wiring Assistance After Engine Swap

    Not sure what that means. I don't think anyone in this thread advised that, although it will crank if you jump it correctly. You never answered the questions about getting 12v at the white wire when in the start/cranking position. Sounds like you were in the run position, which should have 12v...
  19. nola mike

    1989 vs 2008 4.3 differences

    Bend what to the side? There's a baffle in the pan preventing anything from reaching the bottom. Merc uses a whole different tube assembly on the newer engines. Although I guess I'm not sure if the new pan started with the vortec heads or earlier
  20. nola mike

    1989 vs 2008 4.3 differences

    At least on mine, the dipstick was shorter than the tube already and didn't need to be cut. The tube extends to the bottom of the oil pan on the marine engine so you can suck out the oil. If you cut the tube you'll need to access the drain plug to change the oil (I don't think a hose through the...
Top