Search results

  1. C

    Kill Switch installation

    some lanyar kill switches will allow a restart if the captian went for a swim with the cord yet... a helper could restart the engine before going over the falls.
  2. C

    new to me 1970 Johnson 25hp tiller short shaft. locked up

    nothing like a 6 blade shaver .... but you must admit fish prefer to viva in clean aqua :)
  3. C

    new to me 1970 Johnson 25hp tiller short shaft. locked up

    Roadking57...you are a patient man :-) some many good running oldies out there :-) but..... "Patience brings joy" said the cookie
  4. C

    Help with Starter

    fuse seem good. try another fuse or test it for continuity one leg of the fuse should have 12 volts if not backtrace that wire to the +12v source
  5. C

    Need advice on power tilt for 1979 85 HP V4 Johnson

    grenn blue drives the t&T by simply reversing polarity under relaycontrol relays need battery +12 &grd and therest are control wires to the up down switch to flip polarity to the T&T motor
  6. C

    Need advice on power tilt for 1979 85 HP V4 Johnson

    basic t&T 2 wire set up
  7. C

    Lead shot in my 86 25hp evinrude carburetor

    put 2 gyproc srcews on a wood board 3/8 inch appart (top rims) ...easy as pie :) wire one to the engine block wire the other to the plug boot clip see if the spark jumps across. :-) report back !!
  8. C

    Lead shot in my 86 25hp evinrude carburetor

    the rear pulse hole of the pump exposes the diaphragm to the fuel-oil mixture routed to the cylinder ports so it is normal to see it " wet " the inner surface is of course handling the fuel and pushes it to the carb with check valving ...so both surface are ...wet the important issue...
  9. C

    1975 Evinrude 25

    center it between and try it.... if not OK readjust...the marks can't be that far apart :-)
  10. C

    1975 Evinrude 25

    see picture isthis what you are referring to ?? this is an older engine but same principle
  11. C

    1975 Evinrude 25

    so it was the hose ? what was wrong with the old hose.....leaky seal o-rings?
  12. C

    1975 Evinrude 25

    depending on the fuel hose you have .....you have a single or two ended connector hose in the mean time ..... to stop suction air leaks try a few wraps of cellophane and tape around one end (ex: motor side) end ..... see if problem clears up then try the other end and do the...
  13. C

    1996 Ocean Runner 150 trim

    what you ear are the up and down relays likely. The selenoid needs the key to be energized. T&T should operate up and down from the cowl buttons. Dealers have keys... the switch face may have small numbers printed ex:74 identyfying which key you need
  14. C

    Pee tube

    stick a shop vac on the pee hole (adapt the hose accordindly) if you find no blockage if nothing apply air pressure btw it pumps but...did you inspect he impeller coud be just a piece of rubber went up the wtare tube and is stuck
  15. C

    Convert 1993 4 HP to remote tank

    I have installed a Mikuni using a pulse line installed on a side cover and it worked fine .
  16. C

    Pee tube

    or sucking....(vacum) air pressure "could push any crud bacwards
  17. C

    2013 E-Tec 250 (E250DPXABA/S# 5396595) Hard Start

    that filter is on the return fuel supply FROM the injectors.... if your injectors are not clogged :eek: then the return hose must be crumbling !! test it for mushy feeling !! Mecanic should have known because if this a replacement filter (???) and it ended up clogged so fast then...
  18. C

    Convert 1993 4 HP to remote tank

    chinese pumps??? .....I had issues with some rebuiling is tricky to say the least how did you mount the pump ??? the square pumps are pulsed from the rear with a gasket pictures ??? if you have a pulse line you can try a sqware mikuni pump also
  19. C

    Need a little help 150 evinrude intruder lower unit

    this help ? search utubes lots of videos on everything post your year and mdl ## !!!!
  20. C

    1995 Johnson 112 won't stop trimming down

    they come and go.....
Top