Search results

  1. alldodge

    Long trip suggestion boat

    Depends on what you mean by work? Took my Rinker 232 cuddy (sold in yesterday) and went from Louisville down to Pickwick Mississippi and back with wife and son. Would eat at State loges, marina's and such
  2. alldodge

    Wiring harness for 5.7GiF

    Bummer
  3. alldodge

    Rec gas prices???

    And more so if it holds more gas then its worth 😀
  4. alldodge

    How Far Can an Electric Truck Tow?

    Rust are there still autos that get rusted bad? My 2000 sold in 08 had no rust, and the 08 sold in 21 had no rust
  5. alldodge

    Wiring harness for 5.7GiF

    I have not personally tested a 4B this way, they all have the same DLC connector and pin out
  6. alldodge

    Rec gas prices???

    I burn about 5 gal just making it to the main body of the lake
  7. alldodge

    Rec gas prices???

    Go figure, keep hearing folks talk about their truck getting 16 or less MPG. My 2500 diesel is averaging 20 MPG
  8. alldodge

    New main battery Q

    Drawing does not list what it's for but does show it installed. Indicates its sealed, non-spillable but does have vent for (guessing) pressure release. I would leave it inside the box https://www.gobatteries.co.uk/wp-content/uploads/2020/07/Exide-ER550-Data-Sheet.pdf
  9. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    Don't know why they show the extra connections on the newer cable because the pics of the actual part does not have them. It most likely has to do with other things going forward in the manual
  10. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    Ahhh no, and sort of Using pic in post 14, there are 2 types and yours is the one on top with a resistor built into each end of the cable. It shows no resistor is needed with the J box and only using weather caps The another one has only one resistor built into the cable so that end is marked...
  11. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    Hey I want photos, can always use more info :unsure:
  12. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    The older cable 879981T will have a label listing terminator end https://www.mercruiserparts.com/879981t10-harness-assy The newer cable does not https://www.mercruiserparts.com/879968t15-harness-assy
  13. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    Resistors
  14. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    Found some more info but this list 2006 and on
  15. alldodge

    I am a Pawpaw!!!! :)

    Congrats
  16. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    The first part of the manual talks about a harness that is not using smartcraft but is ready (so to speak). This continues how to wire thru page 34. Shows if junction boxes are there but not being used so weather cap is all that is needed. Connector M on page 4 is needed if that type of cable...
  17. alldodge

    New Engine Replacement - Engine Died and Hydro locked after 5 hrs!?

    Need to find out the moisture reading before anything else. If hull is full of water or wood is soaked then your dead in the water. The higher risers will help but may not be enough What were the holes in the hatch used for? You could probably cut them off for clearance. Then get a piece of...
  18. alldodge

    Rinker differences

    The 236 was Rinkers first try into the entry level go-fast boats. The cuddy is smaller (not as tall). The 236 didn't go over very well so they increased the height of the cuddy and changed the seating and called it 232. 236 has 2 buckets and a single row rear seat 232 has 2 buckets and a wrap...
  19. alldodge

    A mercruiser 4.3l MPI with a low weak idle hard to start

    Think that is another puzzle is with the water pressure showing zero the available power should be less then 100%. Also I would expect to see guardian mode active
  20. alldodge

    2001 Optimax SmartCraft Wiring / Questions

    Think of the CAN buss as a hose filled with water and the terminator(s) seal the ends so the water will stay filled. If a terminator is left off then the water keeps pouring out. You can use a 4 port junction box but all ports not used must have terminators for it to work. Also with just...
Top