Search results

  1. R

    Can you weld a broken tiller arm gear 1983 15hp Evinrude

    Make it more robust then when it left the factory.-----Perhaps a piece of 3/8 stainless rod or tube.-----If using the tube then cut and fit pieces into it.----Perhaps 5/16" bolt in either end.-----I am just pulling sizes at random but you get the idea.-----No way would I pay to get that...
  2. R

    Can you weld a broken tiller arm gear 1983 15hp Evinrude

    Big $$$ item.----I had better not throw any more of them out.----Your location ?-----I would make a replacement myself !---Your local machine shop could make that part.------You could get it welded I suppose.----So many options.
  3. R

    1980’s Evinrude - Temp Warning System?

    Post a picture of the cylinder head of your motor.---Close up.-----Is there a location for a sensor switch ?----Should be easy to spot on a 1985 model.
  4. R

    Neutral start switch 1983 15hp Evinrude

    The start switch and neutral switch are the same $$$$ part.-----You could switch them.-----Or simply bend adjust the bracket that mounts the neutral switch.----Easy I think.
  5. R

    Can you weld a broken tiller arm gear 1983 15hp Evinrude

    There are ways to repair stuff.-----Picture helps to determine.----Do you have a part # of this ---" tiller bar " ?-----I can not recall any part called a " tiller bar " on this motor !
  6. R

    1980’s Evinrude - Temp Warning System?

    Model # of your motor ?
  7. R

    1980’s Evinrude - Temp Warning System?

    If you are handy you could add the warning horn to your motor.
  8. R

    1979 Johnson 100hp V4

    Do you know what was done for the " rebuild "-----Was it new rings on old pistons.----Bored out with new O/S pistons ?------I would be removing the 4 bypass covers to inspect pistons and rings.
  9. R

    1980’s Evinrude - Temp Warning System?

    Model # of your motor?---Why did you not install the correct impeller.-----A new impeller every 5 years is the way to go.----Some electric start models did have a warning horn.
  10. R

    Choosing an Inboard for homebuilt 20' Glen-L Runabout Monaco

    Find a ski boat with a V-8 Mercruiser ( inboard ) or similar for all the parts you would need
  11. R

    $50 150hp Gambling project (pics)

    If it is the part added for the dual cable steering at the motor , how did you determine that would be expensive ??
  12. R

    What are these holes for in this carbeurator drain manifold

    I believe that is correct.---One hose from earlier crankcase ventilation was fitted there.
  13. R

    Choosing an Inboard for homebuilt 20' Glen-L Runabout Monaco

    Find a donor boat with V-8 Mercruiser.-------That would have everything needed for the installation.----Often available for $1000 or less.
  14. R

    2012 15 HP Honda Outboard cutting out when giving it throttle.

    Compression seems low for a 4 stroke.-----Open low speed mixture screw 1/8 turns at a time and see if bogging goes away.
  15. R

    Chrysler Fuel Pump Numbers?

    Landeverde----Perhaps test run with another hose and tank.----Fuel pumps a driven by crankcase PRESSURE pulses.-----So see if there is an issue there.
  16. R

    Looking for help !

    There is no way that I would spend money for a new fuel pump.----They are easy to inspect and repair.----Have you checked water pump ?-----Motor going into the ---S.L.O.W. -----mode due to over heating ?
  17. R

    $50 150hp Gambling project (pics)

    I doubt the boat was parked because a broken steering system.
  18. R

    Olympics

    I was awarded a trophy years ago in hockey.----Most sportsman like player and I played defense.-----.Today I say if I was the referee in some NHL games there would be no one left to play the game after 10 minutes.-----I often said it too.-----Players get a 2 minute penalty doing things on the...
  19. R

    $50 150hp Gambling project (pics)

    Remove bypass covers and inspect pistons and rings.
  20. R

    Piston fit

    So what do your pistons measure 1/2" from bottom of skirt?-----And what do your bores measure just above the ports ?----Post some accurate measurements.
Top