Search results

  1. phillnjack2

    Evinrude 60hp 1995 cdi wiring ? HELP needed

    Hi everyone. The engine is a 1995 evinrude 3 cylinder 60hp Model no BE60TLEOC Serial no G 03751787 yesterday when i lifted the hood of the engine to just have a check around etc,i noticed a broken orange wire . The wire comes from the cdi unit and goes into a 5 pin rubber plug. I have no...
  2. phillnjack2

    Evinrude tacho ????

    I have a evinrude 60hp 3cyl 1995. Model no BE60TLEOC Not had the engine very long, so far it runs like a dream. I Just got the original tacho and a few other bits from the owner who said it all works ok. I cannot fire the engine up at the moment due to not being near a water supply. When i...
  3. phillnjack2

    Evinrude 1995 powertrim seal numbers and types

    I have a 1995 Evinrude 60hp 3 cylinder Model no BE60TLEOC Serial no G 03751787 made in USA The 2 smaller Power trim rams are leaking oil and i need to get new seals/ o rings etc. ive been intouch with BRP and they seam a bit expensive considering it just the seas/o ringsl that i need...
  4. phillnjack2

    Battery amp hour for outboard ?

    What size battery is needed for outboard engines with electric start and trim n tilt ? For example, I have a 60hp evinrude electric start with trim and my friend has a 140hp with electric start and trim n tilt. Now both engines will need a certain amount of cold cranking capacity, and both...
  5. phillnjack2

    Classic boat pic gallery (20yr and older)

    Re: Classic boat pic gallery (20yr and older) Here is my old Dateline Bikini 15 (around 1979) with Volvo penta 70hp She had been neglected and left out in all weathers for around 3 years. The outside looked so bad and interior was torn and tattered. On the way home the day i bought it, the...
  6. phillnjack2

    Dangerous at high speeds

    Re: Dangerous at high speeds Being its a force 85hp you probably aint going as fast as some might think, force 85 is = to about 60hp merc/johnnyrude if your very lucky. sounds like your hull is probably set too much bow down. Bow down can cause severe twist at speed and can throw you out the...
  7. phillnjack2

    Dateline speedboat

    Re: Dateline speedboat why put something in the archives when people are posting and reading this today. Ive only just seen this thread and would like to put my two penneth in. I had a dateline Bikini, and to be honest i thik they were crap . Nothing to do with build quality,just...
  8. phillnjack2

    Morse C3000 ob hydraulic steering pics ?

    Hi can anyone please tell me if there is a metal gasket or washer that goes under the dash on the morse C 3000 hydraulic steering helm unit to take some strain from the dash ? Ive recently got a complete Morse C3000 ob hydraulic system secondhand for my boat, but when looking at the helm it...
  9. phillnjack2

    Evinrude 60hp No Beep at control box !!!!

    Hi i have a 1995 evinrude 60hp, model BE60TLEOC. My question is this. I do not hear the beep when i turn the key on that so many people seem to have on their control box. :eek: I have disconnected the VRO wiring at the engine, i did this as soon as i picked the engine up due to not trusting the...
  10. phillnjack2

    Tohatsu TLDI MD40B2 - TLDI MD50B2 UPRATING ?

    Hello can someone tell me what is needed to uprate a 2010 Tohatsu TLDI MD40B2 to a TLDI MD50B2 UPRATING ? in other words, how do i uprate a 40hp to a 50 on this model engine. I cannot find any mechanical differences as in cc etc between the two, is it just a simple matter of bigger jets or is...
  11. phillnjack2

    Mercury 4hp 1990 shift rod problem !!!

    Hello i have a 1990 mercury 4hp single cylinder 2stroke. Today i took off the lower unit to check the impellor for any cracks breakages etc. When i was moving the lower unit ,i accidently lifted it by the shift rod !!!!! Now i cannot seem to be able to engage the gears F.N.R by moving the rod ...
  12. phillnjack2

    Evinrude 50hp driveshaft stuck, cant get leg off

    Ok we have a 50hp evinrude 1987. the model of engine is E50TLCUD the engine has not been very well looked after at all and maintainance as been almost zero. The engine belongs to a friend and im now trying to get everything sorted out for him for the up-comming season. To say this engine is...
  13. phillnjack2

    evinrude 50hp 1987 carbs spitting back and misfiring

    Hello First of all i will explain what is happening, and then hopefully someone might be able to help or give some usefull advice. A friend has a 1987 50hp evinrude, it used to be vro but its now on premix with everything to do with vro taken of and discarded. This engine has sat for about 3...
  14. phillnjack2

    Tohatsu 25hp runs good wot, wont run slow for long ?

    Ok this is a wierd one for me. But im sure there is planty of good advice from those who know about these engines. 25HP tohatsu 2 stroke. from first starting it will idle ok in nuetral then put in gear,give it wide open throttle and it takes off real good. Infact power is instant. It will run...
  15. phillnjack2

    Getting more power from a suzuki 30hp

    What is the simplest and easiest way of getting more power from a 2 cylinder 2 stroke suzuki 30hp year 1983. Ive seen on the johnson/evinrude engines forum about putting on bigger carbs etc, but is this an option with the suzuki dt30 ? Ive heard that better reeds might give a slight boost in...
  16. phillnjack2

    8000 rpm tacho for suzuki ?

    i have a suzuki dt30 2 cylinder 2 stroke year 1983 engine serial number 03001 304012 electric start longshaft . I am trying to fit a rev counter (tachometer) to keep a check on revs ,but not having much luck. From what i gather i need to put positive to the + and negative to the - and...
  17. phillnjack2

    Suzuki Dt 30 prop ? what else fits ?

    Does anyone know what props fit a suzuki DT 30 2 cylinder 2 stroke ? I have looked around and hardly ever see any secondhand props for this engine. It a 10 inch to 10.3 inch diameter and 10 splines . Is there any other engine makes that use the same prop as this engine, in the 10 to 15 inch...
  18. phillnjack2

    Tohatsu m25A2

    can anyone give me any idea on the specs of Tohatsue m25A2 engines. a pic of one would be good to see original colours if possible. from what i can make out, its a about 1980 ish, i know this one is shortshaft. the prop is not thru exhaust, and wonder what other props might fit it ? any info...
View older results
Top