Search results

  1. M

    Hp too much,?

  2. M

    Hp too much,?

    Was that motor mounted on a jack plate or did the dealer install it right to the transom effectively casing the prop to be 5 inches lower than designed?
  3. M

    Yamaha 130 hp 25 inch on 20 inch transom

    Holy crap that's a nice motor.
  4. M

    Yamaha 130 hp 25 inch on 20 inch transom

    The whole midsection would need to be replaced as well as the driveshaft seems like a ton of work and $. Might sell it after I buy it and use the money towards a 20 inch 130 hp. This one was very well kept and I'd love to make it work though
  5. M

    Yamaha 130 hp 25 inch on 20 inch transom

    Here's a video he sent me on his boat on the 5 inch bracket.
  6. M

    Yamaha 130 hp 25 inch on 20 inch transom

    He's giving me the jackplate but I don't think I want to set the motor that far back from the transom
  7. M

    Yamaha 130 hp 25 inch on 20 inch transom

    So are people preferring the 3 inch adjustable jack plate or these 1/2 inch thick riser plates? I was thinking the riser might be better because it mounts closer to the motor? Either way I'm buying the motor due to a great price then I can decide what to do
  8. M

    Yamaha 130 hp 25 inch on 20 inch transom

    The yamaha in the pic is on a 5 inch jack plate for his 20 inch transom. It's definitely a 25 inch motor. He added a piece of starboard to keep water from coming in when chopping the throttle. Here's another pic. His boat is a 20 ft bullet center console originally an outboard motor hull.
  9. M

    Yamaha 130 hp 25 inch on 20 inch transom

    Would I be better off with this 3" jackplate? Description states used for 25 inch motors on 20 inch transom
  10. M

    Hp too much,?

    Ok so I'm leaning towards the 130 hp. Sorry for multiple threads
  11. M

    Hp too much,?

    Looking at a yamaha vmax 175 hp 2 stroke hpdi 20 inch shsft. I have a wellcraft 190 ccf with max hp rating of 150. Is this a bad idea? Looks like It weighs about 100 lbs more than a 130 yamaha picture is my current setup
  12. M

    Yamaha 130 hp 25 inch on 20 inch transom

    I'm assuming I'd need to swap the driveshaft as well? Do I have to pull the powerhead to swap the mid?
  13. M

    Yamaha 130 hp 25 inch on 20 inch transom

    My boat is a 1997 wellcraft 190 ccf with a 20" transom. I want to install a 1999 yamaha 130 on it but it's a 25" motor. Not interested in swapping midsection and driveshaft. The seller is giving me the bracket he used to run this motor on his boat (it's in the pic of the yamaha 130). I also...
  14. M

    Checking power trim sender

    So that would be at the 2 wire connector?
  15. M

    Checking power trim sender

    Working on trim guage again. I disconnected the triangle connector and put a jumper from the white with brown stripe pin to the sender on the guage. I also put power and ground to the guage. The guage is not changing when tilting motor up and down. I also jumped the white with brown stripe wire...
  16. M

    Checking power trim sender

    Can you tell me where to attach the pressure guage on the powerhead?
  17. M

    Checking power trim sender

    Ok I guess I'll check back at the motor to see what's going on. Thanks
  18. M

    Checking power trim sender

    Anybody have an answer as to if the white with brown stripe wire in this harness connector is for trim guage signal?
  19. M

    Checking power trim sender

    I looked all under the dash. Not finding the 3 loose wires with ring terminals. I found a white with brown wire in a connector with no wire coming out the other side of the connector in line with the white with brown wire. I put power and ground to the guage and jumpered a wire from that white...
  20. M

    Checking power trim sender

    Probably not I found a round connector under the hood with wires from the sender. I think 1 black and one white with brown . How do I test at that connector?
Top