Search results

  1. M

    Adding charging system to 1997 evinrude 25 hp

    Do I need a whole new plate or are there provisions on the current plate to mount the stator?
  2. M

    Adding charging system to 1997 evinrude 25 hp

    Hi. What's it take to add charging capability to 1997 evinrude 25 hp manual Start tiller motor 2 stroke 2 cylinder? I imagine I'll need a component under the flywheel, a rectifier, some battery cables? Since it's manual start where do the battery cables hook to since there is no starter or...
  3. M

    Reliable sure lube hubs

    Thank you that's very helpful
  4. M

    Mariner 9.9 length

    Ok thank you
  5. M

    Mariner 9.9 length

    Picked up a 1995 mariner 9.9 2 stroke. The motor Measures just under 18 inches from where clamp bracket rests on top of transom down to cavitation plate. Is this considered a short or longshaft? Thank you
  6. M

    Reliable sure lube hubs

    These don't have the rubber plug. They are a solid metal cap with a grease nipple in the center.
  7. M

    Reliable sure lube hubs

    Yeah but how do you know how many pumps to do?
  8. M

    Reliable sure lube hubs

    Going on a trip soon have a question. My boar trailer has reliable sure lube brand hubs (the kind where only a zerk fitting sticks out). I pumped 20 pumps of grease in but don't see it coming out if the inner seal or spindle or hub. Not sure if I did that right. Bearings were packed 2 years ago...
  9. M

    98 johnson 25 hp bolt torque and sequence

    Anyone have the bolt torque and tightening sequence for 1998 johnson 25 hp 2 cylinder 2 stroke for the following Head bolts and sequence Head bolt cover and sequence Exhaust cover bolts and sequence Thank you
  10. M

    Honda 25 flywheel removal

    Might have to pull flywheel on 2001 honda bf25a. I'm used to working on 2 strokes. How do I go about this. Usually there are three holes around the center of a flywheel to thread the puller bolts into. This one doesn't have holes there?
  11. M

    Honda 25 no spark

    I was jumping the starter solenoid to check for spark on my recently purchased 2001 honda bf25a. I had spark on all 3 cylinders when I first checked it. Spark seemed weak but that was due to me using a manual starter trigger across both big terminals on the solenoid. I decided to put a...
  12. M

    Honda BF25 remote to tiller conversion

    Picked up a 2001 honda 25 hp short shaft electric start remote control style motor. I want to make it a tiller. Honda sells a conversion kit with handle and bracket and wiring with key switch for close to 400.00. Problem is it says it's for 2004 and newer but I don't see why it won't work on a...
  13. M

    Polr 15. Throttle cable

    Hi I have a 1944 johnson polr 15. 22 hp military motor brand new in crate never ran. I've had it for 15 years. I'm kicking around the idea of uncrating it and getting it to run. The throttle cable is broken where it attaches to the carb. Anyone have an idea where I can get a new or used cable...
  14. M

    Evinrude 40 hp primer not working

    Thanks that's helpful
  15. M

    Evinrude 40 hp primer not working

    The purple wire was secured to the terminal block that shares its connection with another purple wire. I should note there is a 4 wire harness coming from the underwood harness and the wires aren't connected to anything. The seller said at one tiime a switch was hooked to these wires so that the...
  16. M

    Evinrude 40 hp primer not working

    It's a tiller. No key
  17. M

    Evinrude 40 hp primer not working

    Working on a 1995 evinrude 40 hp tiller. The fuel primer isn't getting power. I tested the switch is good and the primer itself is good. I tried switching to a different rectifier but same thing. The rectifier I used came from another motor so I'm not positive that it is good. Could a bad stator...
Top