Search results

  1. M

    93 evinrude 25 hp primer

    Not sure if this is an issue I have to have the idle mix screw turned out counter clockwise about 3 1/2 turns to keep it from sneezing. I cleaned the carb by taking it apart and blowing through all the ports including removing the soft plug on the top. I installed the new soft plug on the top...
  2. M

    93 evinrude 25 hp primer

    Next issue is I have to have the idle mix screw turned out counter clockwise about 3 1/2 turns to keep it from sneezing. I cleaned the carb by taking it apart and blowing through all the ports. This is a all metal carb no plastic top with the adjustment on the side of the carb. Compression dead...
  3. M

    93 evinrude 25 hp primer

    Seems to run fine just surprised to see fuel exiting the hose when it's not connected
  4. M

    93 evinrude 25 hp primer

    93 evinrude 25 hp tiller manual primer. When taking small primer hose off of the nipple on the top of the carb I am getting pulses and mist from the end of that small primer hose when engine is running. I confirmed the primer knob is pushed all the way in. Seems like this hose will always see...
  5. M

    Recoil pawl evinrude 25 hp

    Ok 👍 thanks all
  6. M

    Recoil pawl evinrude 25 hp

    Ok. I loosened the half inch bolt on the underside and moved the sheave counter clockwise until the arrow was pointed at the words arrow here. Then retightened the bolt. Seems better now
  7. M

    Recoil pawl evinrude 25 hp

    How about giving me the procedure to time it if you don't mind
  8. M

    Recoil pawl evinrude 25 hp

    Not sure what to do. I guess I'll pull it back off
  9. M

    Recoil pawl evinrude 25 hp

    Ok I fixed the recoil installed 2 new pawls and 3 missing wires that connect the pawls. When I pull the rope handle the rope pulls out around 5 inches or more before making engagement with flywheel. Is there a way to shorten the distance the rope has to be pulled before it engages the flywheel?
  10. M

    Recoil pawl evinrude 25 hp

    Yeah looks like I need 3 wires and 2 new pawls and e clip for the missing pawl
  11. M

    Recoil pawl evinrude 25 hp

    There is a spot for a second one but the clip and wire are not there. Did some use only one??
  12. M

    Recoil pawl evinrude 25 hp

    Early to mid 90s evinrude 25 hp 2 cylinder. Need the blue plastic pawl on the underside of the recoil starter. Anyone know if thar part is available separately? Part number? This is the plastic piece that flips out to engage the flywheel. Thanks
  13. M

    Ignition plate hold down evinrude 25 hp

    I used taller washers ang got the spacing correct. I'll order the screw and washer set I see on ebay or can I just use it the way I have it with some washers stacked to make the right height?
  14. M

    Ignition plate hold down evinrude 25 hp

    Decals are missing and it's in primer
  15. M

    Ignition plate hold down evinrude 25 hp

    Serial number tag is missing. Soft plug on block doesn't contain serial number or model number as I've seen on some motors so not sure of the model number. It's a short shaft tiller motor with front shift handle.
  16. M

    Ignition plate hold down evinrude 25 hp

    I installed the plate to block ring with screws but now the plate bottom is contacting the throttle rod not allowing the rod to return to slow position. Seems like I need more clearance between the block and the ring. I put washers on top of the threaded holes on the block then screwed the ring...
  17. M

    Ignition plate hold down evinrude 25 hp

    working on early 90s 25 hp 2 stroke 2 cylinder motor. The ignition plate is loose. I pulled the flywheel and found all 4 nuts loose or not in place. I'm used to screws holding this bottom plate on not this stud and nut arrangement. The threads are very short for the second nut to go on and some...
  18. M

    1996 50 hp adjustment question

    How do I test the. Overheat horn? The temp sensor is a single wire connector for your reference
  19. M

    1996 50 hp adjustment question

    Yes Guage is accurate. Was a low hour motor. I did the test on a cold motor. It's been sitting for many years. I'll check it again after I've ran it for bit
  20. M

    1996 50 hp adjustment question

    Yes I'm cleaning the carbs, installing a new impeller, new prop shaft seals, etc. Compression shows 165 psi on both cylinders
Top