Search results

  1. lindy46

    Evinrude Lark 6 Generator Question

    I'm looking at buying a 40hp Lark 6 and it has a "charging device" - is it a generator like on the older models or had they gone to alternators at that point? I assume it is not needed for the engine to run? I would prefer to just remove it. Any problems with that?
  2. lindy46

    1961 Merc 400 Lower Unit Questions

    Well, I got the lower unit off the motor and replaced the impeller. What a challenge getting that key back in place:eek:. Anyway, when looking down from the top, should the shift shaft be turned all the way counterclockwise to put the unit in forward gear? It seems that no matter where I...
  3. lindy46

    1961 Merc 400 Impeller Change Challenges?

    So I got the tool to remove the water pump cover, and am ready to attempt the impeller change. Any tips, tricks, secrets I should know about when attempting to remove the lower unit? Apparently there is no shift rod to disconnect on a merc like on a Johnnyrude. So is it just a matter of removing...
  4. lindy46

    1957 Brooklure Restoration

    A few pics of the Brooklure 500 I've been working on the last few moths.
  5. lindy46

    More problems - Merc 400

    One problem after another working on this motor:(. I'm trying to pull the flywheel to replace the timing belt. I have a fairly expensive harmonic balance puller that came with a variety of hardened bolts. NONE of them will fit the threads on the flywheel. I tried numerous bolts I had in the shop...
  6. lindy46

    1955 Brooklure Fuel Pump

    Well, got this old Brooklure 500 (5hp) Up and running and she runs great for a 55 year old motor. This motor has a built in fuel tank, but it also has a fuel pump so you can use it with an external tank. The fuel pump was disconnected when I bought the motor. So anyway, some questions: 1. The...
  7. lindy46

    Merc 400 Fuel Lines

    I'm replacing the fuel lines on a 1961 Merc 400 45hp. Got the original lines with the brass ends. I'm wondering if the screw threaded connections which go into the carbs should have any kind of sealant. The parts list doesn't show any o-rings, but seems like there should be something on those...
  8. lindy46

    Recoil Starter Problems

    I just picked up a 1955 Brooklure 500 5hp which is basically the same as a Johnson 5.5hp. I'm having problems with the recoil. The pawls do not pop out when you pull the rope. I have compared it to a recoil from a 1956 30hp and the mechanism is basically identical. When you pull the rope on the...
  9. lindy46

    1961 Merc 400 - Changing impeller

    Looks like a special tool is needed to get to the water pump impeller. Can this cover be removed in any other way? I've looked on Ebay for the tool and have had no luck. Anyone know where to find one? Also looks like a similar tool is needed to remove the prop shaft cover. Are they the same tool?
  10. lindy46

    '56 Johnson 15hp waterpump/driveshaft mystery

    I was working on this '56 15hp Johnny for a neighbor. Needed new impeller and prop shaft/shift shaft seals. Took it apart, replaced the seals, had to remove the skeg to get to the shift shaft seal. Inspected all the gears. Put it back together and the Driveshaft was riding too low in the lower...
  11. lindy46

    Merc 400 45hp - spark plug wire removal

    I got my factory service manual which covers my 1961 4 cylinder merc 400. I looked in it to find out how to remove the spark plug wires from the distributor cap - it gave three methods: 1. Screw in and out 2. Pull out 3. Held in by screws. Anyone know which is the method of attachment on this...
  12. lindy46

    Lubriplate 105 in geacase? 35hp Lark

    Last winter, I replaced all the seals in my 1957 35hp Lark. Pressure tested OK. Filled it up with gear oil and put it in the water in the Spring. Just pulled it out of the water, and drained the L/U. Oil was real milky! Pressure tested it again for 3 hours and it held 12psi. I turned the drive...
  13. lindy46

    1961 Merc 400 - Spark Plug Gap

    Well, I finally got the cowl off and checking the plugs. It has Autolite 295 plugs in it - is that correct? What is the proper gap?
  14. lindy46

    1961 Mercury 45hp Questions

    Well, this lifetime Johnnyrude owner has gone and bought a Mercury! I know nothing about Mercs but couldn't pass up this deal. It is on a 1961 Starcraft Arrow, and it is in awesome condition. I posted a few pics, but there are more posted in the Boat Forum. Anyway, the seller said: 1. In the...
  15. lindy46

    Look what I bought today!

    A beautiful 1961 Starcraft Arrow with a Merc 400. Boat is unbelievable - looks like new. Floors are solid, as is the transom. Hull looks perfect. Finish is shiny with nary a spider crack anywhere. All the rubber moldings are soft and flexible. Upholstery is near perfect. Seat frames wood is...
  16. lindy46

    1956 Evinrude Lark - Ready for water!

    So here's some pics of my latest project - a "56 Lark. I ended up converting it to 12 volt. Had a 12v starter from a '58 but the bolt pattern was slightly different on it. So, had to open up the bolt holes some to get it to fit the '56 starter bracket. Worked like a charm! Got a 12v choke...
  17. lindy46

    1956 Evinrude Lark - 6 Volt?

    I've been working on a 1956 Lark 30hp. Got the electrical in good order and carb rebuilt, lowe unit seals, and now have the wiring harness sorted out. I was just getting ready to fire her up from my 12 volt car battery and got to thinking - hmmm- I think this is a 6 volt system. Am I correct...
  18. lindy46

    What A Find!

    Picked up two complete 1956 Evinrude Larks and a parts motor for $200! Both motors have good compression and are good candidates for restoration. One has new coils, the other has one new coil and one that needs replacement (don't know why he didn't replace both at the same time.) Also included...
  19. lindy46

    Can you believe this?

    Check this out: http://cgi.ebay.com/VINTAGE-1958-K-O-JOHNSON-TOY-OUTBOARD-MOTOR_W0QQitemZ120448993523QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item1c0b51c8f3&_trksid=p3286.c0.m14&_trkparms=65%3A7%7C66%3A2%7C39%3A1%7C293%3A1%7C294%3A50 A toy motor going for more money than the real thing -...
  20. lindy46

    1957 Lark Vibration

    Over the winter I put a "new" lower unit on my 35 Lark because I was having clutch dog/forward gear problems. Since then, I've had a vibration at mid-speed range. Whole pontoon vibrates, like a massaging lounge chair:). I thought maybe the old prop was out of balance, so changed it out, but...
Top