Search results

  1. C

    1957 Johnson 18 hp. FDE-11

    if you have air pressure loss use soapy water spray bottle and find the leak . check for bubbles ...... like checking a inner tube flat :-) on a bike vacum loss may be stopped with a temporary coating of grease on suspect junctions or tightly wrap in cellophane wrap on easy access...
  2. C

    Location of impeller 1971 Johnson 4HP weedless outboard

    drop the GC remove pump cover replace impleller ...bit of sop or greas to slide it in the pump housing turning clockwise looking down take care not to pull out the drive shaft !! ... slide the pump cover up & past the o ring on top reverse procedure to install...
  3. C

    Location of impeller 1971 Johnson 4HP weedless outboard

  4. C

    120HP Looper ignition

    paul...my comment was in reference to 120lopper's pics. ... proceed as you see fit. maybe do a visual on your own to see if you have a similar burn out
  5. C

    Should oil deposits be in the powerhead

    you may want to acces Leroy's web site where the 9.9-15hp family from 1974-2007 is extensively covered here is one of many topics .. http://www.leeroysramblings.com/Johnson%209.9_15.htm plus all the rest...
  6. C

    120HP Looper ignition

    bad pack obvioulsly.. .couple of $2 parts pita to carve out and replace. :-(
  7. C

    #3 fuel injector code

    DO let us know how it turns out. NO inj. are not cheap plus labor. the early 2005 etec injectors are even more expensive and... getting rare :-(
  8. C

    Should oil deposits be in the powerhead

    when a new load of fuel enters the cyl. on the downstroke.. that fuel entering the cyl pushes the burnt fuel oil mix out the exhaust ports. unfortunately the ports being opned during that time will also permit a % of freah fresh fuel oil mix to take the same way out the exhaust...
  9. C

    #3 fuel injector code

    dirt will not show up as an open code but a heat build up due to a clogged screen resulting in reduced cooling by the fuel flow may aggravate things . Like I said up to you. I understand the coil winding is not very tolerant if heat causes the open code and you feel safer with...
  10. C

    30hp carb settings

    generally the cam has a mark on it. (look closely for the 2 small spikes) the mark should meet the cam follower just as the throtlle opens when the throtlle is at START. to line up cam and cam follower there are nuts underneath which you can loosen and pull out or push in the cam...
  11. C

    30hp carb settings

    it is an old style with a carb fix jet for the HS and a needle for LS you can adjust just gently seat the needle closed and back it out 1.125 turns ... warm up the motor adjust mid way between rich and lean a bit on the richer side
  12. C

    #3 fuel injector code

    up to you if swapping is fine go for it. hopefully you are familiar with ETEC injectors. each has a coefficient profile which must be loaded in the EMM to replace the previous profile of the defective injector. A bit of brain swap & the non-initiated could kill the EMM . lots of...
  13. C

    #3 fuel injector code

    Jake... agree a new injector would clear up the problem but just out of curiosity have you aver dug deeper and try to find the cause of these overheats. thanks
  14. C

    #3 fuel injector code

    no expert on much some would say but ...injectors are just electromagnets timed to allow fuel to reach the cyl for cimbustion the inner coil winding is basically good (continuity at a few "x" ohms) or open (R.I.P.) they can fail mechanically or electrically fail .. possibly...
  15. C

    9322B evinrude 9.5hp (not working)

    9.5 carb info with link& sync...
  16. C

    9322B evinrude 9.5hp (not working)

    just to let you I have a 9622a which is a hard starter a small shot of fuel or carb cleaner in the carb grid above the carb gets it going everytime. I have adjusted the float cleaned the carb etc... ls and hs circuits yet it remains a hard starter...but it will puur all day with...
  17. C

    Engine won't start in neutral

    CHECK YOUR PM BOX
  18. C

    1975 evinrude 15504C engine cover...argh!

    any chance you can drill a very small hole (to be pached later and painted over) and insert a small spray can plastic straw to shoot the release agent (PB or WD 40) directly on the lock mecanism hook . you could even drill from the underbelly where it won't even show cosmetically.
  19. C

    9.9 Evinrude - Hard Start when warm , but starts fine when cold

    My apolology did not mean to come out that way. I am certain with the help of SME's a solution will be found to help out 909
  20. C

    2005 175 Evinrudes

    great knews thanks for the feedback. another happy FICHT owner ;-)
Top