Search results

  1. R

    starter pawl on Evinrude 25R77S keeps getting chewed up

    Look closely , there has to be friction / drag on the spring to fully engage the pawl.
  2. R

    55ESL69A electric solenoid assembly

    There were issues with that plunger assembly on the 68 / 69 models.----Look for part that snaps into that socket.----That plunger assembly directs oil pressure in the valve body to move the shift piston / clutch dog.----If in Canada then ----evinrudeparts.ca------Might be able to help.
  3. R

    starter pawl on Evinrude 25R77S keeps getting chewed up

    Not supposed to be grease on those parts.
  4. R

    starter pawl on Evinrude 25R77S keeps getting chewed up

    They used plastic for over about 30 years.----Did someone grease the friction parts that engage the pawl ?-----Pulling gently to engage the pawl first?----Are you using the blue ones?
  5. R

    Drain line on Mercury 7.5 hp motor

    Sorry mate-----It is a 2 stroke engine .----You add oil to the gas only.----But some of that oil ends up near the bottom of the block. ----That hose puts it back to the top of the block.------Oil in the gearcase is totally separate from crankcase.-----Time to read some manuals before launching...
  6. R

    1994 Evinrude 30hp E30ELERM ignition went dead

    There is no VRO system with all those alarms on a 30 HP model.
  7. R

    Force 50 Water coming out of spark plugs (pics)

    The motor needs an overhaul.----Running with wrong prop.----Lugging the motor.----Preignition. ---Overheating. ----Caused the damage to the piston,
  8. R

    Have a j8renm. It had beem sitting for a few years.

    Inspect the little cover on the pump.---Could be cracked.
  9. R

    Need advise on skeg repair on 1991 48SPL Evinrude

    Those gearcases are NOT robust.-----Only a gearcase from 89 to 92 will fit..----I would take that apart for inspection and have a shop weld a new skeg on it,
  10. R

    ‘77 70hp Johnson Repair and Carburetor Rebuild

    Compression should be around 140 PSI -----Perhaps test with a gauge or pull cylinder head for inspection.----You did already install a new water pump impeller I hope.
  11. R

    1994 Evinrude 30hp E30ELERM ignition went dead

    Facts----Get a proper wiring diagram.----The " i wonder what happens if I touch this approach " can cost money in a hurry.----Powerpack / stators / coils are not cheap.---The warning buzzer may be for overheating.----Save money work carefully.
  12. R

    Water Relief Hose Help???

    Well maybe it is just the hose / tube for the speedometer.----Best to post pictures or a very clear description along with model # of the motor.
  13. R

    Adjusting Trim Tab

    When you are behind the boat you turn the fin to the right , if boat takes off to the right.
  14. R

    Cracked block

    What are the chances of cranks in the block that you can not see at this time.
  15. R

    Wheel bearings full of water

    Well----The lower units on outboard motors use seals to keep water out.----Perhaps look into a better seal set-up.----I think I would find a better product to use.
  16. R

    1971 Johnson 2 stroke 4hp leaking lower unit oil out above gear case?

    You mix oil with the gas.-----Some of that oil does not get burned.-----It leaks out of the exhaust.------Keep an eye on the lower unit.-----If water get in replace the seals.-----Or pressure test the lower unit.
  17. R

    '88 Evinrude model difference.

    Yes it does look like a nice paint job with custom decals.-----Pictures of the powerhead ( cowling off ) would help.
  18. R

    1999 Johnson 50 j50pleea shift rod height?

    You can do damage to the control box / cables when shifting with either motor not running or propshaft not turning.-----Just some of the finer points on outboards that folks do not understand !----When the motor is running the gears ( pinion / forward / reverse ) are all turning !
  19. R

    Unfindable(so far) gremlin

    Perhaps some do not know the difference between the 2 types of magnetos !
  20. R

    1972 merc 110 Blue Stripe hood, Ser# 3267158 Exhaust/Steam? coming out taletail

    ???----There is no head gasket on your motor !!!----A water jacket gasket.----But no cylinder head gasket.
Top