Search results

  1. C

    J115PL4SR Fuel issue.

    things to check vst filter clean ? vst float working ok ? when were injectors cleaned last ?? you may have a high pressure filter t the output of the VST... btw do you have EV diagnostics to check for faults...
  2. C

    No crank!?! Electric issue??

    so did you install the proper amperage rated fuse....??? then what happen did the fuse blow ?? if it blew right at KEY ON remove any extra accessories hooked up on the accessory post of the switch ... just pull the ACC wire and retry if ok and fuse no longer blows at KEY ON you...
  3. C

    No crank!?! Electric issue??

    when in doubt replace it ... if it was not blown you will have a spare :) google HOW TO TEST A FUSE .... utubes and how to use a VOM https://www.youtube.com/results?search_query=testing+with+VOM
  4. C

    No crank!?! Electric issue??

    do you have a fuse on that motor ... generally the B+ tapped off the solenoid to the key is fused see typical wiring with the fuse on purple...also check any connectors for corrosion. https://maxrules.com/graphics/omc/wiring/77-78_55HP.jpg purple becomes a yellow-red to the solenoid via the...
  5. C

    What happens if timing is off?

    this post is 12 years old .... best to open a new one
  6. C

    Power trim fluid / refill

    information only: in modern ETEC T&T evinrude recommends a special "Bio oil" in their T&T . my T&T was leaking and could not raise my engine. After much debate on the necessity to use bio=$$$$$ oil my t&T was refilled years ago with regular Evinrude T&T mineral oil . Never had...
  7. C

    Slow start?? New battery, cables, starter, solenoid

    Same with the boat being in neutral as it cranks without the spark plugs out. I know the engine is not seized because the flywheel spins freely that said why not drop the LU/GC and retry btw doest idle ok when started in neutral ? one would not normally start in gear anyway and it...
  8. C

    Evinrude E15Rccs carb cover plate

    presumably this one les than 20$ .... as to gluing.... crazy glue overlaid with baking soda becomes rock hard and may work even be reshaped....but the parrt is inexpensive to set the glue in 1 second as small pray bottle with 1-2 onces of rubbing alcool mixed with 1-2 pea sized...
  9. C

    make remote start and add key switch

    what year and model |??? red + and black _ to the starter just tells you the starter works. 12 feet of wires to the front typically involves RED fused power B+ key ... B post accessories Purple... start (S post yellow-red via neutral switch ) back to the solenoid...
  10. C

    Start solenoid

    Not certain there is a plug diag. is just for guidance only and may not apply to his model#s which we still do not know :)
  11. C

    Start solenoid

    btw the above reflects one way of going things to get a starter to start spinning. post your model #s depening on wiring starter control may pass via a safety neutral interrupt . some systems use a ground to get the solenoid/starter going as in modern ETECs a wiring diagram /service...
  12. C

    Start solenoid

    solenoid have 2 main posts IN (form batt) and OUT ( to starter) and a smaller control post. if you apply batt B+ to the IN post... the solenoid must be activated with the key at START to pass B+ over to the starter ....the normal way it works B+ on the IN post with a starter...
  13. C

    Compression too high?

    A car dealer once told me a Kia Borego had excellent fuel consomption to which I said " Are you telling me your elephant eats less than mine" ? 155 psi on a 27 year old enigine with unknown run hours 1000 miles away. ? options: seller is huffing and puffing the numbers his mecanic iffy...
  14. C

    Compression too high?

    comp aside a 1000 miles is a 1000 miles if anything goes South. have you searched the local market to compare.
  15. C

    Compression too high?

    bring your own known good meter :-) and if not 155 bargain his price down for not being full honest
  16. C

    Power Trim goes up but not down on Johnson Outboard Motor MODEL NO J30PL4SD

    relay contacs probably burnt and allows some current down wise but won't pass all the amps needed to drive the motor.
  17. C

    Badge for cowling

    try aomci ask a member classifieds I think these are available as reproductions... originals certainly rare know anybody with 3d scan & printing abilities ?? tried searching the web ?? http://www.nymarine.ca/EVINRUDEmedallions.html
  18. C

    Power Trim goes up but not down on Johnson Outboard Motor MODEL NO J30PL4SD

    ?? which plug reversing plug wires only doesn't tells you why the relays are not doing the job for you in the down mode. Does it go down with the UP switch ? if so all you have done is use the UP circuit to power the DOWN relay at least we know the blue green wiring is OK what...
  19. C

    Lower unit shift rod wont screw back in

    pivot bolt must be installed to secured properly. otherwise all I am saying is par t#12 may be tilted a bit preventing the line up of the shift rod . try tilting the LU the one way or the other to cause the part 12 to tilt and line up with the shift rod passage. a piece of...
  20. C

    Lower unit shift rod wont screw back in

    if the pivot screw #13 was taken out and not aligned back-in I suspect anything goes since part# 12 may be hard to align with the shift rod
Top