Search results

  1. B

    1995 evinrude possible bad coil or power pack

    ok had my boat out this weekend started fine ran out to my fishing hole ran trolling motor for a few hours started 70hp ran fine to another fishing hole didnt stay more then 15 minutes tried to start 70hp and was idleing like crap put in gear and stalled about four times then all of the...
  2. B

    "SLOVED" 1995 70hp constant beep when key is turned on and wont turn off

    ok my wharing horn stays on as soon as i turn on the key i tried to disconnect the tan wire and it will not shut of unless the ground is off does this mean my warning horn is bad and what causes them to go bad i took the horn out and it will sound if hooked to the positve and gound or the...
  3. B

    1995 70hp evinrude tune up service

    I was thinking of taking my motor to the local omc dealer beeen in bussines over 50 years to have a spring tune up done they told me that they will 1. compression test 2. link and sink 3. new plugs 4. change all filters 5. change lower unit oil 6. set low speed idle they said they run the...
  4. B

    1995 evinrude 70hp crankcase tork value

    good day anyone know the tork value for a 1995 70hp crankcase? this would be the bolts that hold the two halves together it looks like my idle and wot stop bracket has been installed on the wrong bolts its two bolts to high which explains why i didnt have a wot stop or be able to set idle that...
  5. B

    1995 70hp wot stop adjustment ?s

    ok is there an adjustment to stop my shifter handel from going to far forward and opening my carb butter flies past 90 degrees i tried to adjust the trinion nut but its either to far one way which is way to low for idle or the other way which is good for idle but opens the butter flies past 90...
  6. B

    1995 70hp tilt and trim wiring question

    i just upgraded my motor from a 1974 70hp to a 1995 70hp i used my old controls but my old motor did not have tilt and trim now the switch on the motor works fine i want to add a switch on my dash do i need the tilt and trim harness with the 5 pin plug from the engine and a three prong for the...
  7. B

    Which stator brand to buy?

    ok looking for a new stator for my 1974 70hp johnson looking on ebay i found two original nos omc no warrenty 185.00 or aftermarket cdi two year warrenty 170.00 just looking for opinions on which one will last longer dont ever want to take of that flywheel ever agian thanks Bob
  8. B

    kicker motor mounts and trailering

    looking to add a 8hp kicker to my 16' boat for long days of trolling does anyone have one mounted on there boat and leaves the motor on it while trailering just want to if the mount is rated for trailering thanks bob
  9. B

    1974 johnson 70hp stator?

    i just noticed recently that i have some brown sticky stuff dripping from the bottom of my stator coils does this mean its getting hot or is just the insulation breaking down the motor runs great other wise and the stator checks out ok with my ohm meter thanks Bob
  10. B

    switching a 1974 70hp to 1996 60hp johnson

    thinking of buying a newer outboard will my controls from my older johnson work with this new of an engine if not anyone know what type of controls i need old motor has no t/t new motor has t/t and vro thanks Bob
  11. B

    1972 johnson 50hp reliable?

    going to look at a boat tommorow with this engine on it any opinions good or bad thanks bob
  12. B

    1989 8hp remote control box ?s

    ok in the process of converting 8hp from tiller to control box control my question is my 1974 70hp came with an extra single lever remote control box any reason why i can't use this one instead of buying a two lever one thanks Bob
  13. B

    mid 80's 6-8hp johnsons electric start

    does anyone know if this platfrom was ever converted to electric start thanks Bob
  14. B

    1989 johnson 8hp stop button?

    other than pulling the lanyard kill switch on the tillier is there any other stop button on the engine? Thanks Bob
  15. B

    converting 89 8hp tiller to remote control?

    is there any way to convert an 1989 johnson 8hp tiller to a remote control box not worried about electric start just throttle and gear shifting thanks Bob
  16. B

    what size flywheel nut 70hp johnson

    any know the size of the flywheel nut for a 1974 70hp johnson its bigger than my 1 1/4 socket thanks Bob
  17. B

    my new jupiter windshield

    had to change it out looks like a brand new boat before and after pics the old windshield and frame are free to anyone here that may need one i am in cleveland ohio Bob
  18. B

    michigan wheel prop # ?'s

    i have what i believe to be a michigan wheel prop on my 1974 johnson 70hp nowhere is the size or pitch stamp on it the only numbers stamped on it are on the center hub they are pj 81 and 564 ou anyone know what size and pitch this may be thanks Bob
  19. B

    1975 sator work on a 1974 70hp

    will a 1975 stator work on a 1974 70hp i have good running 74 johnson and have a 1975 evinrude parts motor i was poking around and noticed my trigger coils are starting to leak under the flywheel well i want to change it with my parts motor one but the newer one doesn't look like my old one...
  20. B

    adding power tilt and trim

    I want to add power tilt and trim to my 1974 70hp johnson is this a striaght forward job looks just to be swapping out transom brackets thanks Bob
Top